-
simu_gps
捷连惯导和GPS组合导航,利用kalman滤波进行数据融合并输出(Jie Lian INS and GPS navigation, the use of kalman filter for data fusion and output)
- 2008-01-16 11:30:20下载
- 积分：1
-
led run
说明： stm32f407 跑马灯实验 原子个例程 学习模块(stm32f407 led run stm32f407 stm32f407 stm32f407)
- 2019-04-25 11:10:51下载
- 积分：1
-
代码
本人用石川法求齿轮的啮合刚度，完整版的程序，里面可以运行啮合刚度图(Meshing Stiffness of Gears Calculated by Ishikawa Method)
- 2019-01-04 16:42:20下载
- 积分：1
-
1123
基于导频的OFDM信道估计的硕士论文一篇，研究信道估计的各种方法(OFDM channel estimation based on pilot master' s thesis a study of channel estimation the various methods)
- 2012-07-26 11:59:34下载
- 积分：1
-
db94361b-3df7-4b5f-83ec-0e6cf5f2e3bd
说明： qam调制误码率比较,包含对16QAM、32QAM、128QAM的误码率分析，并作出误码率比较的仿真图。(QAM modulation bit error rate comparison, including 16QAM, 32qam, 128QAM bit error rate analysis, and make a bit error rate comparison simulation diagram.)
- 2020-12-29 12:50:29下载
- 积分：1
-
5_TD-LTE系统Turbo编码器实验
说明： 使用MATLAB软件，实现TD-LTE系统Turbo编码器的设计。(Using MATLAB software to designe the turbo encoder of TD-LTE system .)
- 2019-12-16 21:55:06下载
- 积分：1
-
UsingProtocol
说明： 自己实现的基于串口通讯发送短消息的低层协议JAVA代码，对于初学者有一定的参考和帮助价值，特意上传上来共享一下！(Their own realization of serial communication based on sending short messages JAVA code low-level agreement, for beginners there is a certain degree of reference and to help the value of deliberately upload up to share about!)
- 2008-11-18 10:20:14下载
- 积分：1
-
VB_Modbus-RTU
VB6.0与变频器的RS485或Modbus通讯，控制变频器的参数设定，运行状态，运行频率，读当前状态，电流，电压，频率，故障等。支持远距离控制。(VB6.0 and drive the RS485 or Modbus communications, control the inverter parameter settings, operation status, operating frequency, read the current state, current, voltage, frequency, fault and so on. Support remote control.)
- 2011-05-13 22:21:12下载
- 积分：1
-
ts170
可以得到很精确的幅值、频率、相位估计，基于K均值的PSO聚类算法,光纤陀螺输出误差的allan方差分析。( You can get a very accurate amplitude, frequency, phase estimation, K-means clustering algorithm based on the PSO, allan FOG output error variance analysis.)
- 2017-06-01 16:48:51下载
- 积分：1
-
Si100x_SPI0_Slave
HLP A+ Modbus 标准通讯协议格式，上位机发送数据格式，正确时变频器返回数据格式(This bit will be set to logic 1 when the receive buffer has been read and contains no
new information. If there is new information available in the receive buffer that has
not been read, this bit will return to logic 0. RXBMT = 1 when in Master Mode.)
- 2013-11-15 11:31:43下载
- 积分：1
