-
modulationanddemodulationcode
交全面的给出了好几种调制解调方案的matlab代码,又ASK,BPSK,FSK,QAM等的源代码
对通信领域的研究人员很有帮助(submit a comprehensive given several modulation and demodulation program Matlab code, ASK, BPSK, FSK, QAM the source code for communications research in the field of staff helpful)
- 2007-01-15 22:51:30下载
- 积分：1
-
Matlab-utility-one-hundred-cases
Matlab的一百个入门小实例，可供新手参考。(The one hundred small entry Matlab examples for novice reference)
- 2013-09-21 22:08:45下载
- 积分：1
-
WaterFiling
Water- Filling Algorithm
- 2011-12-15 06:36:34下载
- 积分：1
-
802163c-01_46
Analysis of PHY waveform Peak to Mean Ratio and Impact on RF Amplification
- 2007-12-27 11:05:16下载
- 积分：1
-
allmatlab
说明： matlab使用基础,MATLAB数据可视化显示与图形处理,MATLAB数值分析(use Matlab based MATLAB data visualization display and graphics processing, numerical analysis of MATLAB)
- 2006-04-05 01:18:10下载
- 积分：1
-
MPSKMQAMmudulation
说明： 本程序用于完成BPSK、QPSK、pi/4QPSK、OQPSK、8PSK、16QAM、32QAM、64QAM和128QAM的调制仿真。并可任意扩展到MPSK和MQAM。程序分成四个部分，fir.m对基带码元序列进行脉冲成型，可选矩形脉冲，升余弦脉冲和平方根升余弦脉冲； modal.m 为主程序，完成岁各种信号的基带星座图映射、脉冲成型和调制；pi4QPSK.m 为pi/4QPSK信号的星座图映射程序；test1.m给出一个简单的频谱显示测试。(This procedure for the completion of BPSK, QPSK, pi/4QPSK, OQPSK, 8PSK, 16QAM, 32QAM, 64QAM and the modulation 128QAM simulation. Arbitrary and may be extended to MPSK and MQAM. Procedures are divided into four parts, fir.m of baseband symbol pulse sequences forming, optional rectangular pulse, raised cosine square root raised cosine pulse and pulse modal.m-based procedures, the completion of the age range of the base-band signal constellation diagram mapping, pulse shaping and modulation pi4QPSK.m for pi/4QPSK signal constellation diagram mapping procedures test1.m given spectrum shows a simple test.)
- 2021-04-12 10:58:58下载
- 积分：1
-
linear-programming
可用于解决线性规划方面的问题，是《精于matlab最优化计算》一书中的源程序(linear programming)
- 2011-09-17 21:02:54下载
- 积分：1
-
yucekongzfangzhenliangshuru
广义预测控制GPC多变量预测控制源程序代码(Generalized predictive control (GPC) Multivariable Predictive Control)
- 2013-03-16 20:28:24下载
- 积分：1
-
用Z-N法实现P，PI，PID控制的参数整定
用MATLAB程序软件完成Z-N法对控制器的参数整定，实现P,PI,PID控制器的分别参数整定，并求出控制器的控制参数Kp，Ti，Td。最后绘制出不同控制器控制下的及参数整定前后的单位阶跃响应图进行比较。(MATLAB program software is used to complete the parameter tuning of the controller by Z-N method. The parameters of P, PI, PID controller are adjusted, and the control parameters of the controller Kp, Ti, Td are obtained. Finally, the unit step response diagram before and after parameter tuning is plotted under different controller control.)
- 2021-03-18 10:49:20下载
- 积分：1
-
MATLAB-statistics
介绍MATLAB在概率统计中的若干命令和使用格式，这些命令存放于MatlabXToolboxStats中。(Probability and Statistics in MATLAB to introduce a number of orders and the use of format, the commands stored in MatlabX Toolbox Stats in.)
- 2009-05-01 09:38:23下载
- 积分：1
