-
卫星通信中数字调相信号调制方式识别方法研究
针对数字卫星常用的 7 种通信信号调制方式(QPSK、8PSK、16QAM、32QAM、64QAM、16APSK、32APSK)，对零中心归一化瞬时幅度谱密度最大值、四次方谱、幅度、高阶累积量四种特征参数进行了分析，提出了一种联合特征参数的信号调制识别方法．(Aiming at seven communication signal modulation modes commonly used in digital satellite (QPSK, 8PSK, 16QAM, 32QAM, 64QAM, 16APSK and 32APSK), four characteristic parameters of zero-center normalized instantaneous amplitude spectral density, quadratic spectrum, amplitude and high-order cumulant are analyzed, and a signal modulation recognition method of joint characteristic parameters is proposed. Method.)
- 2020-06-21 09:20:02下载
- 积分：1
-
TD_DCA
基于matlab的TD-SCDMA动态信道分配(Matlab-based TD-SCDMA, dynamic channel allocation)
- 2009-11-01 15:22:32下载
- 积分：1
-
OReillyGoogleHacks
O Reilly Google Hackes is the most wanted book for SEO and SEF optmizations in the world. This is the full version in .pdf format
- 2010-02-15 08:49:53下载
- 积分：1
-
CoOFD_callOptiSystem
OPTICAL COMMUNICATIONS MATLAB calls OptiSystem CO-OFDM.
- 2020-10-16 21:47:28下载
- 积分：1
-
rcgiv
仿真图是速度、距离、幅度三维图像，插值与拟合的matlab实现，计算两个矩阵之间的欧氏距离。( FIG simulation speed, distance, amplitude three-dimensional image, Interpolation and fitting matlab implementation, Calculation of the Euclidean distance between the two matrices.)
- 2017-05-19 09:48:13下载
- 积分：1
-
Study-on-the-Control-Scheme
恒频恒压(CVCF)逆变电源的输出电压波形质量是衡量其性能的重要指标之一。文章采用一种重复控制和双闭环控制相结合的电压波形控制策略，以重复控制器提高逆变电源输出电压的稳态精度，减小总谐波畸变率；以双闭环控制器达到较快的动态响应速度。该方案在一台采用TMS320F240 DSP控制芯片的50 Hz三相PWM逆变器上得到验证。(Constant voltage constant frequency (CVCF) Inverter output voltage waveform quality is an important measure of its performance indicators. Paper using a repetitive control and the combination of double closed loop control voltage waveform control strategy to improve the repetitive controller output voltage inverter steady-state accuracy and reduce total harmonic distortion to achieve a faster dual-loop controller dynamic response speed. The program uses TMS320F240 DSP in a 50 Hz phase control chip PWM inverter has been to verify.)
- 2011-05-17 11:02:50下载
- 积分：1
-
CNC-Control-Code
西門子CNC系統編程代碼表,對初學者幫助很大(Siemens CNC system control code )
- 2013-07-26 11:36:00下载
- 积分：1
-
Y1197129
宽带射频功率放大器的数字预失真技术研究论文，学习资料(Broadband rf power amplifier digital predistortion technology research
)
- 2011-05-09 22:18:44下载
- 积分：1
-
Soft_ware-CRC
基于51单片机的CRC算法的C语言实现(文档内含源代码)(Based on 51 MCU CRC algorithm C language implementation (document containing the source code))
- 2009-10-31 11:15:24下载
- 积分：1
-
ADIBEAM
ADIBEAM
Abstract—the increase in navigation accuracy demanded by
EGNOS and Galileo and their future evolution encourages the
study and design of advance receiver architectures. In that
direction, the ADIBEAM project focuses on the design of high
accuracy ground stations, specifically GNSS Reference Stations, in
order to improve its robustness in front of multipath and
interference errors with the goal of achieving centimeter level
tracking accuracy. The adoption of antenna arrays and digital
beamforming at the ground reference station receivers is one of
the most promising approaches to cope with errors induced by
multipath and interference.
- 2012-01-23 23:20:55下载
- 积分：1
