网站首页

TS

于 2014-11-17 发布文件大小:610KB

 0  210

下载积分: 1 下载次数: 1

我要下载

代码说明：

说明： Ts模糊神经网络程序matlab代码，用于风电相关研究的数据训练及测试(Ts fuzzy neural network application matlab code )

文件列表：

TS
..\40can.mat,424520,2013-12-26
..\data.mat,191249,2013-12-26
..\gzdata.mat,7309,2013-12-26
..\xunce.m,5950,2013-12-26
..\yuce24.m,1890,2013-12-26
..\yuce40.m,1868,2013-12-26
..\程序说明.txt,158,2014-03-24

下载说明：请别用迅雷下载，失败请重下，重下不扣分！

发表评论

0 个回复

APF_IP_IQ
基于IP-IQ瞬时功率理论的APF仿真波形图，三相三线，如果需要还可以将三相四线传上来供大家学习交流。(Based on the IP-IQ instantaneous power theory of APF simulation waveform, phase three-wire, if necessary, can be three-phase four-wire pass up for the Learning Exchange.)

2012-03-23 15:12:05下载

积分：1
test16qam
星形16QAM过基带信号产生。经过升余弦成型滤波和高斯信道(Star 16QAM baseband signal generator over. Been raised cosine pulse shaping filter and Gaussian channel)

2010-05-28 11:23:37下载

积分：1
5l
A commonly used control device called a programmable logic controller, or a PLC, is used to read a set of digital and analog inputs, apply a set of logic statements, and generate a set of analog and digital outputs. Using the example in the previous paragraph, the room temperature would be an input to the PLC. The logical statements would compare the setpoint to the input temperature and determine whether more or less heating was necessary to keep the temperature constant. A PLC output would then either open or close the hot water valve, an incremental amount, depending on whether more or less hot water was needed. Larger more complex systems can be controlled by a Distributed Control System (DCS) or SCADA system.

2013-08-16 16:54:36下载

积分：1
shanChen
多相流动lbm计算，实现shanchen模型(Multi-component fluid, using a LB method, based on the Shan-Chen model)

2011-10-08 21:40:26下载

积分：1
PDControlQuadrotor
This file contains the simulink simulation of the PD control of a Quadrotor. Quadrotor model is take

2013-04-13 02:53:22下载

积分：1
Boost_Converter
说明：升压转换器是一种DC / DC电源转换器，可将电压从其输入（源）升至其输出（负载）。在连续导通模式下（流经电感的电流永远不会降为零），升压转换器的理论传递函数为：占空比在哪里0.5 在此示例中，转换器从250 V电源馈送RC负载，并且PWM频率设置为31 kHz。模拟运行仿真并观察示波器上的波形。确认负载电压（Vout）的平均值非常接近理论值：Vout = 250 /（1- 0.5）= 500V。(A boost converter is a DC/DC power converter which steps up voltage from its input (source) to its output (load). In continuous conduction mode (current through the inductor never falls to zero), the theoretical transfer function of the boost converter is: where is the duty cycle.0.5 In this example, the converter is feeding an RC load from a 250 V source and the PWM frequency is set to 31 kHz. Simulation Run the simulation and observe waveforms on Scope. Verify that the mean value of the load voltage (Vout) is very close to the theoretical value of: Vout = 250 / (1 - 0.5) = 500 V.)

2020-03-22 20:41:56下载

积分：1
MATLAB
MATLAB控制系统仿真与实例详解（附书光盘）(MATLAB demo)

2010-03-14 14:07:55下载

积分：1
ALOHA
ALOHA协议程序。[Traffic,S,Delay]=aloha(capture)(ALOHA protocol procedures。[Traffic,S,Delay]=aloha(capture))

2012-05-18 14:14:07下载

积分：1
fft--demo
matlab写的一个FFT例程，对初学者很有帮助(matlab FFT DEMO)

2013-09-20 16:24:16下载

积分：1
IntelCodeTable
Intel Code Table for assembly developers

2014-12-15 00:09:00下载

积分：1

696518资源总数
106182会员总数
24今日下载

TS

0 个回复

热门标签

热门下载