登录
首页 » matlab » ferman

ferman

于 2013-03-27 发布 文件大小:6KB
0 166
下载积分: 1 下载次数: 1

代码说明:

  Code used by Ferman (2011) in the matlab.

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • The_dual-port_RAM-based_FPGA
    基于FPGA的双口RAM实现及应用,对RAM有一个系统的介绍(The dual-port RAM-based FPGA Implementation and Application of RAM to have a systematic introduction)
    2010-07-05 11:35:55下载
    积分:1
  • OFDM_BPSK_QPSK_MSK_QAM
    OFDM仿真BPSK,QPSK,MSK,QAM,信道为AWGN和Rayleigh信道(OFDM simulation of BPSK, QPSK, MSK, QAM, AWGN channel and Rayleigh channel for the)
    2010-12-06 11:07:11下载
    积分:1
  • svpwm
    说明:  SVPWM源代码,内含simulink组合功能(SVPWM source code)
    2011-03-27 15:04:52下载
    积分:1
  • ALAMOUTI-SFBC-MIMO-OFDM-WITH-N=512---QPSK
    ALAMOUTI ALGORITHM CODE FOR OFDM
    2014-03-07 16:38:36下载
    积分:1
  • capacity-of-ZF-and-MRT
    关于MIMO天线的matlab仿真,有代码和仿真结果图(Matlab simulation on MIMO antenna with code and the simulation results)
    2021-04-15 11:38:54下载
    积分:1
  • jiangwei2
    降维状态观测器是非常重基于T变换的降维观测器设计方法。要的一类观测器(Reduced-order state observer is very important dimension reduction based on T transform observer design method. To a class of observer)
    2010-07-16 11:41:01下载
    积分:1
  • ltfat-0.97.2
    The Linear Time/Frequency Toolbox (LTFAT) is a Matlab/Octave toolbox
    2010-08-20 17:09:53下载
    积分:1
  • Time_ana
    对确定的一个负反馈系统,进行稳定性判断、最小相位系统判断;求取零点、极点、放大系数;绘制阶跃响应图。(To determine a negative feedback system, judge, judge the stability of minimum phase system calculating the zeros, poles, amplifying coefficient drawing step response diagram.)
    2015-01-19 20:36:40下载
    积分:1
  • testcon
    一个数学模型的优化 function testcon() %% 设置初始值,上下限; x0=[18 13 11] lb=[3 0.1 7] ub=[25 1 25] %% 调用优化求解函数(testcon) (Optimization of a mathematical model function testcon () set the initial value, the upper and lower limits x0 = [18 13 11] lb = [3 0.1 7] ub = [25 1 25] Call for Function Optimization (testcon))
    2007-10-18 10:08:29下载
    积分:1
  • parag
    H=CIRCLE(CENTER,RADIUS,NOP,STYLE) This routine draws a circle with center defined as a vector CENTER, radius as a scaler RADIS. NOP is the number of points on the circle. As to STYLE, use it the same way as you use the rountine PLOT. Since the handle of the object is returned, you use routine SET to get the best result.
    2009-05-09 14:53:00下载
    积分:1
  • 696518资源总数
  • 105877会员总数
  • 14今日下载