-
keilc51.jsp
KeilC uVision3，最新的keil C编程软件，可以编写51单片机的程序（keilC或汇编语言）(KeilC uVision3, the latest keil C programming software, you can write 51 MCU programs (keilC or assembly language))
- 2010-01-18 14:22:31下载
- 积分：1
-
measure-24-ways-of-impulse
说明： 本人编写的一段小程序，单片机通过8255a扩展端口，实现3*8=24路低频脉冲信号的测量，采用的特别的软件算法，具有使用价值。通过串口和上位机通信。(this is a small source code i have written. i use 8255a to rich ports for MCU in order to measure 24 ways of impulse. it is practically in use.)
- 2010-03-26 11:30:42下载
- 积分：1
-
power_divider_based_ADS_simulation
这是一个基于ADS的功分器制作的PPT，从理论到实践仿真，比较全面，以供参考。(power divider based ADS simulation.)
- 2010-05-27 10:26:01下载
- 积分：1
-
Automatic-tester-resistance
本程序实现基于单片机的自动电阻测试，包括AD芯片的使用和继电器的控制。(This procedure to achieve automatic resistance measurement based on single chip microcomputer, control and relay includes a AD chip.)
- 2014-02-10 12:40:25下载
- 积分：1
-
bh1750程序
说明： 通过bh1750与stm32连接，检测光照强度并显示在液晶屏(Through the connection of bh1750 and STM32, the light intensity is detected and displayed on the LCD screen)
- 2020-05-27 03:02:36下载
- 积分：1
-
24xled
说明： 24C08多花样流水，采用51开发板，编程使LED呈流水灯，初学者的好例子。(24C08 multi-pattern, running water, with 51 development board, program the LED lights were water, a good example for beginners.)
- 2011-04-07 15:47:24下载
- 积分：1
-
scp1000(0)
基于单片机的便携式高度计系统，可移植性高。(Microcontroller-based portable altimeter system, portable high.)
- 2011-08-09 21:35:58下载
- 积分：1
-
PWM_IR-stm32f103c8
stm32f103c8t6上面实现uart3的Irda功能接受红外字符，控制TIM4上面4个通道的pwm输出占空比(stm32f103c8t6 functions to achieve the above uart3 acceptance of Irda Infrared character, control TIM4 above 4 channel pwm output duty)
- 2013-11-22 10:43:37下载
- 积分：1
-
433Mhz解码程序
说明： 433MHz decode
- 2020-02-17 16:53:36下载
- 积分：1
-
practice1
工程教育中级练习题1：按一下K1键，LED以10Hz频率闪烁，屏幕上画出红圈，跟着闪，放开后保持该频率闪烁；长按K1键超过3秒，LED以5Hz频率闪烁，屏幕上画出红圈，跟着闪，放开后保持该频率闪烁；按一下K2键，LED熄灭；按一下K2键，LED常亮。(Secondary Exercise Question 1 in Engineering Education: Press the K1 key, the LED flickers at 10Hz frequency, draw a red circle on the screen, follow the flash, and keep the frequency flickering after release; Press the K1 key for more than 3 seconds, the LED flickers at 5Hz frequency, draw a red circle on the screen, follow the flash, and keep the frequency flickering after release; Press the K2 key, the LED goes out; Press the K2 key, the LED always shines.)
- 2019-05-15 23:01:13下载
- 积分：1
