登录
首页 » matlab » SOSMC

SOSMC

于 2014-11-28 发布 文件大小:15KB
0 183
下载积分: 1 下载次数: 25

代码说明:

  In this Simulink model, a second order sliding mode controller is developed for a nonlinear system.

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • face_detection
    说明:  实现人脸检测的功能,对合适大小的图像,将其放在相应的matlab文件夹下即可自动进行人脸检测并定位。(For face detection function, the size of the image on the right, put it in the appropriate folder automatically matlab for face detection and localization.)
    2010-04-21 11:10:32下载
    积分:1
  • cx
    说明:  用matlab做的车牌识别的程序,能运行,效果还不错!(License plate recognition using matlab to do the procedure can run, results were pretty good!)
    2010-05-10 17:59:01下载
    积分:1
  • ContrLib
    用MATLAB的脚本语言M语言编写的,用于在MATLAB环境下实现帕笛近似(高阶模型简化降阶)的程序源代码,可以在MATLAB环境下直接运行。(MATLAB M scripting language language, MATLAB environment for the realization of Palau under Di approximation (high-order model to simplify Reduction) program source code, in the MATLAB environment direct operation.)
    2007-04-04 13:15:01下载
    积分:1
  • ImprovedSegment
    改进的基于区域的图像分割算法,对含有噪声的图像非常适用!在matlab6.5下顺利编译通过 (Improvement on the region's image segmentation algorithm for noisy images very well! In matlab6.5 smoothly through the compiler)
    2007-04-29 21:46:31下载
    积分:1
  • dbf2800df370
    包含MVC,GMV等的几种控制系统性能评估算法。还不错,分享一下(Generalized minimum variance control)
    2013-12-21 22:52:00下载
    积分:1
  • eeg-denoise
    EEg信号去噪,使用阈值法实现,并对去噪前后的信号完成比较,以实现去噪(failed to translate)
    2013-05-06 19:15:22下载
    积分:1
  • 4_2
    In the following figure is a system of two water tanks. Mass flow into the top tank at a fixed rate q0 and exits this tank through an orifice of area A1. This exit water then flows into a second tank which has an orifice of area A2 at its bottom. Each tank has constant cross section of area A, with A>>A1,A2. (a) Determine the ODE model which governs the heights z1 and z2 of water in the system. (b) Determine the equilibrium given a fixed rate q0. (c) Linearize the system model about the equilibrium. (d) Compare the step responses of the nonlinear model and linearized model by choosing reasonable system parameters. ( (b) Plot the flow v.s. pressure drop curve with the estimated c to validate your estimation
    2012-11-30 15:58:41下载
    积分:1
  • HHT
    希尔伯特黄变换的源代码及其MATLAB软件包(HHT code)
    2010-12-20 10:24:51下载
    积分:1
  • cavity
    lattice boltzmann code for cavity flow
    2010-06-03 03:43:27下载
    积分:1
  • niudun_qianxiangchazhi
    数值分析——利用牛顿前向插值方法计算atanx的Newton形式的系数(Numerical analysis- interpolation using Newton' s method to calculate atanx before the Newton form factor)
    2011-07-07 19:22:15下载
    积分:1
  • 696518资源总数
  • 105885会员总数
  • 31今日下载