登录
首页 » matlab » fengzhi

fengzhi

于 2013-03-29 发布 文件大小:2KB
0 161
下载积分: 1 下载次数: 2

代码说明:

  在所考虑的时间间隔内,变化的电流、电压或功率的最大瞬间值。 (In the considered time intervals, change the maximum instantaneous value of the current, voltage or power.)

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • Principles-of-Communication-Systems-Simulation-wi
    Principles of Communication Systems Simulation
    2013-11-28 17:07:00下载
    积分:1
  • TLS3001(2012-11-10)
    STC单片机驱动TLS3001LED芯片源码(STC microcontroller chip driver source TLS3001LED)
    2013-11-20 19:11:29下载
    积分:1
  • 485programme
    485通讯程序,用的TXT写的程序,改为.C的后缀就可以了(485 communications procedures, used to write procedures TXT changed. C suffix can be a)
    2008-03-03 10:01:39下载
    积分:1
  • 24C02
    51单片机对串行存储器 24c02的 读写程序 (Serial memory 24c02 literacy procedures)
    2012-09-18 09:30:56下载
    积分:1
  • simcom-sim5218
    modem SIM5218 mobile network communication
    2013-09-25 02:21:14下载
    积分:1
  • ATT7022B-STC12C5A60S2
    AT702三相电采集芯片,采用STC12C5A60S2控制,能准确测量出三相电的有功功率无功功率,电压电流等所有电参数。(AT702 three-phase power acquisition chip, using STC12C5A60S2 control, can accurately measure the three-phase power active power, reactive power, voltage and current and all other electrical parameters.)
    2020-11-17 00:09:40下载
    积分:1
  • leyard2000
    256级灰度屏leyard2000驱动芯片滚动字幕带时钟(STM32+3.5固件库)(Marquee 256 grayscale screen leyard2000 driver chip with a clock (the STM32 3.5 firmware library))
    2012-02-19 09:42:19下载
    积分:1
  • BMD_PCIE
    自己根据xapp1052修改的源代码,已经编译成功,并应用在开发板上。(According xapp1052 own modified source code has been successfully compiled and used in the development board.)
    2015-10-19 08:10:20下载
    积分:1
  • DMA+多路ADC+定时器+均值滤波
    说明:  基于stm32f103的多路ADC采集,将采集的电压传入到DMA设定的内存中,在通过均值滤波得到比较准确的数据(Based on the multi-channel ADC acquisition of stm32f103, the collected voltage is transferred to the memory set by DMA, and the more accurate data are obtained by means of mean filter.)
    2020-06-21 11:00:02下载
    积分:1
  • matlab-simulink-Inverted-Pendulum
    本论文中,以一级倒立摆为研究对象,对它的起摆以及稳定控制做了研究,主要研究工作如下: 1.首先介绍了倒立摆系统的组成和控制原理,建立了一级倒立摆的数学模型,对倒立摆系统进行定性分析,但在平衡点是能控的、能观的。 2.分析了倒立摆的起摆过程,对倒立摆的起摆能量反馈控制进行分析与说明。 3.在matlab2014a的simulink库下对倒立摆构造单级倒立摆状态反馈控制系统的仿真模型和构造具有状态观测器的单级倒立摆状态反馈控制系统的仿真模型。 4.对这次仿真的总结。(In this paper, in order inverted pendulum for the study, since it swing and stability control to do the research, the main research work is as follows: 1. The first introduces the composition and control principle of inverted pendulum system, the establishment of inverted pendulum The mathematical model of inverted pendulum system for qualitative analysis, but at the equilibrium point is controllable, and can view. 2. Analysis of the inverted pendulum swing the process of inverted pendulum swing the feedback control of the energy analysis and explanation. 3. Under matlab2014a the simulink library to construct a single-stage inverted pendulum swing state feedback control system simulation model and the structure has a state observer status feedback single-stage inverted pendulum control system simulation model. 4. Summary of the simulation.)
    2015-01-15 11:54:40下载
    积分:1
  • 696516资源总数
  • 106658会员总数
  • 16今日下载