-
satimage
extreme learning machine 例子
run satimage_mean(extreme learning machine examples run satimage_mean)
- 2007-12-16 23:02:32下载
- 积分：1
-
chkmem
PC matlab memory check routine.
:)
- 2009-10-07 06:11:11下载
- 积分：1
-
runDFA
本程序是用来计算去趋势波动分析的MATLAB程序的(This procedure is used to calculate the detrended fluctuation analysis to the MATLAB program)
- 2009-04-01 19:54:28下载
- 积分：1
-
iirfilterdesign
iir filter design low pass and high pass filters ...butterworth and chebyshev
- 2011-02-05 15:12:36下载
- 积分：1
-
Matlab
Matlab中龙格-库塔(Runge-Kutta)方法原理及实现(Matlab, Runge- Kutta (Runge-Kutta) method principle and implementation)
- 2013-12-03 21:04:46下载
- 积分：1
-
gailvsuanfa
这是中国数学建模中编程交流上概率算法内容，里面提供了很多概率算法的例子(This is the exchange of mathematical modeling in the programming content on a probability algorithm, which provides many examples of probabilistic algorithms)
- 2010-11-20 19:41:53下载
- 积分：1
-
LMD(matlab)-01
LMD经验模态分解matlab程序，可以运行的(LMD (Local mean decomposition)(matlab))
- 2012-03-25 15:14:30下载
- 积分：1
-
scilab
Scilab培训教程，scilab是可代替MATLAB的开源软件，其程序语言与MATLAB相似，有很好的发展前途。(Scilab training course, scilab is the open source alternative to MATLAB, the MATLAB language and similar procedures, have good development prospects.)
- 2010-05-12 23:31:02下载
- 积分：1
-
matlab1
控制工具箱与SIMULINK软件应用：系统对象为G(s)=4/s(s+2)
PI补偿器K1(s)=(s+1)/s K2(s)=(s+0.5)/s
a 若由K1(s)与 G(s)串联组成的单位反馈系统，称为系统A。
b 若由K1(s) 放置在G(s)的反馈通道称为系统B。
c 若由K2(s)与G(s)串联组成的单位称为系统C，绘制上述每一种情况的阶跃响应与斜坡响应，求每一种情况下的系统阶跃响应误差与斜坡响应误差，并与理论分析结果进行比较。
(Control toolbox and SIMULINK software application: system object for G (s) = 4/s (s+ 2)
PI compensator K1 (s) = (s+ 1)/s K2 (s) = (s+ 0.5)/s
If a by K1 (s) and G (s) series of feedback system of the unit, known as a system a.
B if the K1 (s) placed in G (s) feedback channel called system b.
If c by K2 (s) and G (s) series of unit is called system c, draw the above each kind of condition of step response and slope response, for each of these cases system step response error and slope response error, and the results were compared with theoretical analysis.)
- 2012-04-19 14:43:49下载
- 积分：1
-
bpsk
用一个双极性基带数据信号对载波进行角度调制产生BPSK信号s(t)=10cos[wct+Dpm(t)]。(With a bipolar baseband data signal generated BPSK modulated carrier signal point s (t) = 10cos [wct+ Dpm (t)].)
- 2011-04-23 14:39:29下载
- 积分：1
