-
VI示例
labview编写串口通讯实例，基于ModBus协议，使用串口通讯，与电机驱动器通讯，实现信号写入与读取，从而控制电机(LabVIEW serial communication, signal writing and reading)
- 2018-12-27 10:27:38下载
- 积分：1
-
FFT
傅里叶变换 LabVIEW的源码 希望对广大学习有些帮助 (Fourier transform LabVIEW source code hope the majority of learning some help)
- 2015-12-09 22:12:50下载
- 积分：1
-
Remote-waveform-acquisition
基于DataSocket节点的远程波形采集，包含服务器端和客户端(DataSocket based remote node waveform acquisition, including server and client)
- 2011-12-13 12:21:55下载
- 积分：1
-
TCP
用labview编写的基于TCP/IP协议的服务器与客户端通信程序。(Prepared using LabVIEW-based TCP/IP protocol server and client communication program.)
- 2007-12-17 08:58:17下载
- 积分：1
-
Snap7
说明： Snap7是一款开源的32/64位多平台以太网通信套件，用于与西门子S7 PLC进行本地连接。 新款CPU 1200/1500，旧款S7200，小型LOGO 0BA7 / 0BA8和SINAMICS Drives也得到部分支持。(Snap7 is an open source 32 / 64 bit multi platform Ethernet communication suite for local connection with Siemens S7 PLC. The new CPU 1200 / 1500, the old S7200, the small logo 0ba7 / 0ba8 and SINAMICS drives are also partially supported.)
- 2021-01-26 12:38:37下载
- 积分：1
-
数据采集编程指南 中篇
NI DAQ应用介绍
1. 一个完整数据采集系统的基本组成部分
2. NI 提供了基于哪些平台的数据采集硬件产品，它们分别适用于什么样的应用领域
3. 数据采集设备硬件选型过程中应该关注哪些重要参数(Introduction of NI data acquisition hardware 1. Basic components of a complete data acquisition system 2. NI provides data acquisition hardware products based on which platforms and which application areas they are suitable for respectively. 3. What important parameters should be paid attention to in the process of hardware selection of data acquisition equipment)
- 2020-06-21 20:20:01下载
- 积分：1
-
readexecl
使用labview读取excel数据，绘制三维曲线和二维曲线(Using labview read excel data, drawing three-dimensional and two-dimensional curve curve)
- 2013-07-30 15:51:53下载
- 积分：1
-
GPIB-Device-Monitor
实现GPIB设备识别列表显示，输出选择的GPIB设备信息，将波形图发送到GPIB接口的示波器设备并显示出来。(For device identification display list GPIB, GPIB output selection device information will be sent to the waveform of the oscilloscope GPIB interface device and displayed.)
- 2016-11-17 15:32:51下载
- 积分：1
-
基于LABVIEW的TCP网络通讯.doc
一个很好的入门材料，介绍了如何使用labview实现TCP/IP网络通讯，可以配合官方manul学习(A good introductory material describes how to use LabVIEW to achieve TCP/IP network communication, can cooperate with official manual learning)
- 2018-12-01 07:58:19下载
- 积分：1
-
strain-to-deform
这是一个在labview上根据悬臂梁厚，梁长，受力点距固定端的长度，应变片距固定端的长度，以及应变片上的数值来测算梁的最大挠度的程序。(
This is a distance in the labview according thick cantilever beam length, the length of the pitch by the force of the fixed end, the fixed end of the length of the strain gauge and strain values on-chip to measure the maximum deflection of the beam of the program.)
- 2015-09-26 16:32:48下载
- 积分：1
