-
hitmatlab
哈尔滨工业大学matlab讲义，幻灯片格式，由浅入深，比较全面(Harbin Institute of Technology matlab lectures, slide format, easy-to-digest, relatively comprehensive)
- 2007-11-14 13:12:13下载
- 积分：1
-
3-DOF-linear-structure1
在分析结构损伤后，给结构添加噪声，再对结构不同损伤情况下的分析(After the analysis of structural damage to the structure adding noise, and then the structure is different in case of damage)
- 2013-10-26 09:53:56下载
- 积分：1
-
gaussian-fitting
针对激光光斑图像或荧光小球等图像进行高斯拟合定位其中心坐标。可同时定位一幅图像中的多个小球。要求对象模型符合高斯分布。(For laser speckle images or small fluorescent balls image gaussian fitting location and its center coordinates. Can be positioning an image of the multiple balls at the same time. Request object model conforms to the gaussian distribution.)
- 2016-09-18 09:44:43下载
- 积分：1
-
MATLAB-Linear-Equations-with-MATLAB
说明： 详细介绍用MATLAB解线性方程组，简单介绍(Details of Linear Equations with MATLAB, a brief introduction)
- 2011-02-25 09:22:36下载
- 积分：1
-
eee
杨氏双缝干涉
两相干光源到接收屏上P点距离r1=(D2+(y-a/2)2)1/2, r2=(D2+(y+a/2)2)1/2,
满足相干条件的光波叠加后，对于观察屏上某一确定点，即r1、r2确定后，叠加后的光强为 式中λ为光波的波长， 、 ，令相位差φ=2π（r2-r1）/λ,
最后可得公式如下：
，
最后光强I=4I0cos2（Φ/2）。
观察相干光叠加后光强的分布.
(Young' s double slit interference two coherent light source to the point P on the receiving screen distance r1 = (D2+ (YA/2) 2) 1/2, r2 = (D2+ (y+a/2) 2) 1/2, meet coherent conditions lightwave after superposition, for a determined point on the viewing screen, i.e. R1, R2 is determined, the superimposed light intensity where λ is the wavelength of light, make the phase difference φ = 2π (R2-R1)/λ, final can be obtained using the following formula: Finally, the light intensity I = 4I0cos2 (φ/2). Observed coherent superposition of light intensity distribution.)
- 2013-01-03 21:04:13下载
- 积分：1
-
cejing
对测井曲线的数值进行分析，并进行自动分层。(The value of the logs for analysis, and automated tiering.)
- 2011-07-28 00:50:41下载
- 积分：1
-
LTE_conv_decoder
conventional decoder for LTE-A
- 2014-10-20 22:33:08下载
- 积分：1
-
simulation-for-pid-control
PID control simulation(matlab simulation for pid controller)
- 2013-09-02 18:31:13下载
- 积分：1
-
piotr_toolbox_V1.03
This toolbox is meant to facilitate the manipulation of images and
video in Matlab. Its purpose is to complement, not replace, Matlab s Image
Processing Toolbox, and in fact it requires that the Matlab Image Toolbox
be installed. Emphasis has been placed on code efficiency and
code reuse.
- 2009-07-21 11:36:24下载
- 积分：1
-
MATCOMVC
说明： 使用MATCOM使VC与MATLAB混编的小例子(VC and MATLAB using the mixed MATCOM small example of)
- 2011-03-27 14:35:55下载
- 积分：1
