-
POWER-ELECTRONIC-SIMULINK-CODES
THESE ARE THE POWER ELECTRONIC SIMULINK BLOCKS
- 2011-06-30 15:40:47下载
- 积分：1
-
ZigBeeIEEE
The implementation was built on Matlab/Simulink using
fundamental components in Simulink to demonstrate how
reliably complex modulation schemes can be built, cost
effectively and efficiently [5]. The design of ZigBee
transmitter using MSK modulation is shown in the Figure 1.
Here we map input data bits to 8-chip PN sequences to be
transmitted and results in a chip rate of two mega chips per
second. After that, resultant chip sequence is send to the serial
to parallel converter. It is used here to separate the odd and
even bit indexed chips. Following this bipolar data formatting
is performed and signal modulated with a 2.4 GHz carrier on
the In Phase and QuadraturePhase data stream and adds it to
get the required transmitter output signal.
- 2014-09-23 20:56:58下载
- 积分：1
-
Tijana_Jevtic_2zadatak
object recognition using convolution
- 2011-01-11 07:38:10下载
- 积分：1
-
Signal-detection-theory
信号检测理论——线性调频信号的匹配滤波处理(Signal detection theory- matched filtering LFM)
- 2014-02-19 20:11:55下载
- 积分：1
-
FIR
四种窗函数设计FIR数字滤波器matlab源码（hant,hamming,blackman,kaiser)(use window functions to design digital low-pass FIR filter...)
- 2009-04-07 12:22:27下载
- 积分：1
-
field-distrubution
field distrubution for non uniform optical medium
- 2011-05-07 20:36:11下载
- 积分：1
-
dataProc
it is a code to process the data of CWB autosite in TAIWAN
- 2012-03-25 16:00:37下载
- 积分：1
-
computerwork_1
1） 借助MATLAB画出误差性能曲面和误差性能曲面的等值曲线；
2） 写出最陡下降法， LMS算法的计算公式（ ）；
3） 用MATLAB产生方差为0.05,均值为0白噪音S(n)，并画出其中一次实现的波形图；
4） 根据2）中的公式，并利用3）中产生的S(n)，在1）中的误差性能曲面的等值曲线上叠加画出采用最陡下降法， LMS法时H(n)的在叠代过程中的轨迹曲线。
5）用MATLAB计算并画出LMS法时 随时间n的变化曲线（对 应S(n)的某一次的一次实现）和e(n)波形；某一次实现的结果并不能从统计的角度反映实验的结果的正确性，为得到具有统计特性的实验结果，可用足够多次的实验结果的平均值作为实验的结果。用MATLAB计算并画出LMS法时J(n)的100次实验结果的平均值随时间n的变化曲线。
6）用MATLAB计算并在1）中的误差性能曲面的等值曲线上叠加画出LMS法时100次实验中的H(n)的平均值的轨迹曲线；
7）对以上实验结果给出一些你认为有价值的讨论。
（在实验中n=1,,…..N,N的取值根据实验情况确定，一般选取足够大以使算法达到基本收敛，本题作业以电子文档PDF格式提供）
(1) With MATLAB to draw the contours of the error performance surface and error performance surface
2) Write down the steepest descent method, the LMS algorithm formula ()
3) using MATLAB variance 0.05, mean 0 white noise S (n), and draw one to achieve the waveform diagram
4) According to the formula 2), and using 3) S (n) produced in 1), the error performance of the contours of the surfaces superimposed on draw using the steepest descent method, the LMS method is H (n) in the iterative process in the trajectory curve.
5) curve to calculate and draw the LMS method using MATLAB with time n (time corresponding to the S (n) of a first implementation) and e (n) waveform reflect a certain time to achieve results not from a statistical point of experiment the correctness of the results obtained with the experimental results of the statistical properties of the available sufficient times the average of the experimental results as a result of the experiment. Calculate and draw the LMS m)
- 2020-12-14 14:29:14下载
- 积分：1
-
用于信号的EMD、EEMD、VMD分解
说明： 用于信号的分解、降噪和重构，实现故障诊断(Used for signal decomposition, noise reduction and reconstruction to realize fault diagnosis)
- 2021-03-30 08:29:10下载
- 积分：1
-
codec_snr_byYikwang
A simple function that takes an image and a mask as the input, perform compression and decompression on the image (color image compression if input image is color), and display the original and reconstructed images side by side. The program should also be able to compute the SNR of the reconstructed image.
- 2010-11-02 10:10:16下载
- 积分：1
