-
bpjd
说明： 直接的源代码形式,没有解压密码,即解即用,也可能有点语法问题,请使用的时候注意一下(direct source code form, without extracting passwords, that solution is used, may be a bit syntax, please use the time to take note)
- 2006-05-01 17:39:14下载
- 积分：1
-
ew_INCOSE2005_MultidiscipMatlab
case study of multi-disciplinary modeling using MATLAB
- 2013-02-12 23:12:06下载
- 积分：1
-
fbilinear
Image Demosaicing by bilinear interpolation method
- 2012-08-25 00:01:01下载
- 积分：1
-
canshuguji
实现在matlab环境下进行参数估计的傻瓜式操作(Implementation in matlab environment parameter estimation operation of a fool)
- 2009-03-30 15:40:21下载
- 积分：1
-
pump
高压共轨系统中高压油泵子系统matlab/simulink仿真模型(high pump submodel of high pressure common rail system)
- 2014-12-25 10:35:42下载
- 积分：1
-
nc2432134
实现三维作图函数，先基于二维作图，然后三维，对于特定函数，取得了良好的效果(Three-dimensional mapping function, the first based on two-dimensional mapping, and three-dimensional, for a particular function, and achieved good results)
- 2011-11-09 20:05:14下载
- 积分：1
-
ISM
产生房间脉冲响应的源代码，在多噪声，多混响的情况下，信噪比很低，信干比也很低，同时伴随着噪声是非平稳的情况。(room impluse response in the nonstation snr sir is very low circumstance)
- 2014-07-23 11:37:25下载
- 积分：1
-
re1
The model used for creating the reference voltage is shown
in Fig. 4. First, photovoltaic output current (Ipv) and output
voltage (Vpv) are passed through a first order low pass filter
with a magnitude of G = 1 and a time constant of T = 0.01
seconds in order to filter out the high frequency components
or harmonics from these signals as shown in Fig. 5 and Fig. 6.
The filtered current and voltage signals (Ipv_F and Vpv_F) are
then fed into the MPPT control block that uses the Incremental
Conductance Tracking Algorithm. An algorithm that is based
on the fact the slope of the PV array power curve shown in
Fig. 7 is zero at the Maximum Power Point (MPP), positive on
the left of the MPP, and negative on the right. The MPP can
thus be tracked by comparing the instantaneous conductance
(I/V) to the incremental conductance (∆ I/∆ V) [11] as in (1):
- 2013-07-23 17:51:25下载
- 积分：1
-
trace_syscalls
Some architectures that allow for 32bit applications to run on a 64bit kernel, do not map the syscalls for the 32bit tasks the same as they do for 64bit tasks.
- 2014-08-09 11:37:33下载
- 积分：1
-
kjtrew.23
This paper presents a new and efficient approach for capacitor placement in
radial distribution systems (RDS) that determine the optimal locations and size of
capacitor with an objective of improving the voltage profile and reduction of power loss.
The solution methodology has two parts: in part one the loss sensitivity factors (LSF) are
used to select the candidate locations for the capacitor placement and in part two a new
algorithm that employs Dijkstra Algorithm (DA) is used to estimate the optimal size of
capacitors at the optimal buses determined in part one. The main advantage of the
proposed method is that it does not require any external control parameters. The other
advantage is that it handles the objective function and the constraints separately. The
proposed method is applied to 33 & 69 RDS. The solutions obtained by the proposed
method are compared with other methods. The proposed method has outperformed the
other methods in terms of the quality of solution.
OPTIMAL C
- 2013-12-16 14:32:22下载
- 积分：1
