登录
首页 » matlab » pmsmdtc

pmsmdtc

于 2020-06-30 发布 文件大小:18KB
0 210
下载积分: 1 下载次数: 675

代码说明:

  永磁同步电机直接转矩控制仿真,按照博士论文中规中矩建立的直接转矩控制模型 (Permanent magnet synchronous motor direct torque control simulation, Ph.D. thesis in accordance with established law-abiding model of direct torque control)

文件列表:

dtc.mdl,127275,2011-10-26

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • pso
    有关粒子群算法的简单编程,对于初学粒子群的人很有帮助(The particle swarm algorithm is simple program for beginners who PSO helpful)
    2010-09-18 08:55:12下载
    积分:1
  • Modeling-of-statistical-methods
    说明:  这是关于统计方法的建模,适合于初学者。希望对大家有帮助。(Modeling of statistical methods)
    2011-02-28 11:21:41下载
    积分:1
  • gaossal
    大地测量学高斯正反算,matlab的gui界面写成的(The geodetic gaussian is positive and negative, matlab GUI interface of written )
    2011-12-27 00:16:24下载
    积分:1
  • Frank-Wolfe算法 matlab
    Frank-Wolfe算法 matlab程序(Frank-Wolfe (matlab))
    2012-01-11 00:16:34下载
    积分:1
  • NSGA-III
    测试可以跑,根据自己情况修改下函数即可. NSGA-III 首先定义一组参考点。然后随机生成含有 N 个(原文献说最好与参考点个数相同)个体的初始种群,其中 N 是种群大小。接下来,算法进行迭代直至终止条件满足。在第 t 代,算法在当前种群 Pt的基础上,通过随机选择,模拟两点交叉(Simulated Binary Crossover,SBX)和多项式变异 产生子代种群 Qt。Pt和 Qt的大小均为 N。因此,两个种群 Pt和 Qt合并会形成种群大小为 2N 的新的种群 Rt=Pt∪Qt。 为了从种群 Rt中选择最好的 N 个解进入下一代,首先利用基于Pareto支配的非支配排序将 Rt分为若干不同的非支配层(F1,F2等等)。然后,算法构建一个新的种群St,构建方法是从 F1开始,逐次将各非支配层的解加入到 St,直至 St的大小等于 N,或首次大于 N。假设最后可以接受的非支配层是 L层,那么在 L+ 1 层以及之后的那些解就被丢弃掉了,且 St FL中的解已经确定被选择作为 Pt+1中的解。Pt+1中余下的个体需要从 FL中选取,选择的依据是要使种群在目标空间中具有理想的多样性。(The test can run and modify the function according to its own situation. NSGA-III first defines a set of reference points. Then the initial population containing N individuals (preferably the same number of reference points as the original literature) was randomly generated, where N was the size of the population. Next, the algorithm is iterated until the termination condition is satisfied. On the basis of current population Pt, the algorithm simulates two-point crossover (SBX) and polynomial mutation to produce offspring population Qt by random selection.)
    2021-01-26 22:38:41下载
    积分:1
  • pulse-generate
    本程序是矩形波的产生。第零步定义了要产生的波形的所有特征参数,矩形波的持续时间WIDTH,矩形波的采样点数POINTS,载波频率为F0,这个频率的最终引入是便于使用RF频率发射波形。第一步包括产生矩形波,并将其调制到RF上,注意,产生的信号的持续时间是矩形波宽度的5倍,这样,总的采样点数就是5*POINTS。同时还应注意,如果要产生一个基带信号,必须设置T0=0.第二步是画出所产生矩形波的源代码。( This procedure is rectangle wave production. Step to produce stage defined the waveform of all characteristic parameters, the duration of the rectangle wave WIDTH, rectangle wave sampling POINTS POINTS, carrier frequency F0, this frequency for the ultimate introduction is easy to use RF frequency emission waveforms. The first step including generating rectangle wave, and modulated to RF, attention, produce the duration of the signal is five times the width of rectangle wave, so, overall sampling POINTS is 5* POINTS. Also, note that if you want to produce a baseband signals must set T0 = 0. The second step is to draw a rectangular wave generated by the source code. )
    2011-05-21 10:52:01下载
    积分:1
  • de_precoding
    TD-LTE 物理层解传输分集预编码matlaB仿真程序(TD-LTE physical layer solution of transmission diversity precoding matlaB simulation program)
    2011-07-13 10:50:15下载
    积分:1
  • SOA_Jiang
    半导体光放大器的模拟与仿真,是很好的研究半导体特性的程序(simulation for semiconductor optical amplifier)
    2011-12-22 22:21:25下载
    积分:1
  • Triangle2D3Node
    有限元方法计算中3角形单元3节点模型建立,可解决平面应力和应变问题(Finite element method to calculate the Triangle 3 nodes model, which can solve the problem of plane stress and strain.)
    2015-01-03 11:10:18下载
    积分:1
  • RepeatFCM
    matlab编写的聚类算法代码,包含常用的各种聚类方法,可以作为聚类的程序包,有很好的使用和参考价值(matlab for clusterings)
    2009-03-16 21:07:19下载
    积分:1
  • 696518资源总数
  • 106148会员总数
  • 10今日下载