-
MATLABshiyanpingtaisheji
本文通过对当前实时控制的应用研究，提出了将离线仿真与实时控制有机结
合起来，利用MATLAB实现对直线单级倒立摆实时控制的思路。经过分析比较，
确定了基于MATLAB的Real-Time Windows Target实时内核开发硬件驱动程序
的实时控制方案，将Simulink生成的仿真模型下载到目标实时内核中运行，驱动
外部硬件设备，实现对倒立摆的控制。文中介绍的在Real-Time Windows Target
实时内核环境中开发第三方设备驱动程序的方法，是构建本实验平台的核心技术
之一，具有普遍适用性，有一定的推广价值。(Based on the current real-time control of the applied research, raised offline simulation and real-time control organically combined to realize the use of MATLAB linear single-stage inverted pendulum idea of real-time control. After analysis and comparison, to determine based on MATLAB)
- 2008-08-22 09:32:32下载
- 积分：1
-
quzao
信号去噪的MATLAB程序，可以参考使用，特别是故障诊断中的信号去噪(MATLAB program, the signal de-noising can refer, in particular, the signal de-noising in the fault diagnosis)
- 2012-08-15 09:55:56下载
- 积分：1
-
jiefangcheng
matlab中解方程的主要命令,和详细的使用方法,希望对朋友门有用!(Solutions of equations in matlab major orders, and detailed the use of, in the hope that useful door Friend!)
- 2008-05-09 18:43:33下载
- 积分：1
-
Lorenz
说明： 在matlab中画Lorenz吸引子的源代码(Lorenz attactor)
- 2010-04-22 11:09:01下载
- 积分：1
-
cloud-
云变换，逆向云发生器实例,打开后即可在MATLAB中运行(examples about cloud transformation and back cloud transformation)
- 2021-04-19 10:48:51下载
- 积分：1
-
xiashan
MATLAB 牛顿下山法的一个小程序，原理就不详细说了。因牛顿迭代法受初值选取的限制，为防止迭代发散，对迭代过程再附加一项要求:|f(x(k+1))|<|f(x(k))|,将牛顿法迭代的结果:x(k+1) =x(k)-f(x(k))/f (x(k))和前一近似值x(k)适当加权平均做为新的改进值:x(k+1)=u*x(k+1) +(1-u)*x(k),其中u(0<>
迭代时u取1开始，逐次减半计算，直至附加要求符合为止。实例计算中x(k)=x(0)不变，只更新u和x(k+1)，直至:|f(x(k+1))|<|f(x(k))|（即|f(x(1))|<|f(x(0))|)，然后更新下山因子为u=1,继续以牛顿法迭代。(MATLAB Newton-down a small program, the principle is not explained in detail. Newton iteration by the initial value of the selected limit, in order to prevent additional iterative divergence, the iterative process a request: | f (x (k+1)) | < | f (x (k)) | Newton iteration Results: x (k+1) ' = X (k)-f (x (k))/f' (x (k)) and a previous approximation x (k), appropriately weighted average as a new improved value: x (k+1 ) = u* x (k+1) ' + (1-u)* x (k), where u (0 < u> iteration take successive calculated at 50 until the additional requirements found so far. examples of calculation of X ( k) = x (0) unchanged profile u and x (k+1, hungry) until: | f (x (k+1)) | < | f (x (k)) | (i.e. | f (x (1)) | < | f (x (0)) |), then profile downhill factor for u = 1, to continue to Newton iteration.)
- 2013-05-15 08:52:09下载
- 积分：1
-
partial_transmit_sequence
THIS IS THE MATLAB CODE FOR PTS TO REDUCE PAPR
- 2014-02-25 11:49:03下载
- 积分：1
-
cioujizi
教学资料，磁偶极子仿真，此处为磁偶极子远区场matlab仿真程序(Teaching materials, magnetic dipole simulation, here for the magnetic dipole far zone field matlab simulation program)
- 2014-07-03 20:48:28下载
- 积分：1
-
xiaoboronghe
它是指将来自同一目标的不同传感器的信息通过一定的算法融合到一幅图上,从而获得比在单幅图上更完整(It is to point to will come from the same target of different sensors through certain information fusion algorithm to a picture on, to get in on the drawing than single more complete
)
- 2012-05-13 16:29:44下载
- 积分：1
-
sinskalman
一段关于捷联惯导系统卡尔曼滤波的Matlab仿真程序，(Paragraph on the SINS Kalman filter Matlab simulation program,)
- 2012-06-08 12:27:18下载
- 积分：1
