-
jiangwei2
降维状态观测器是非常重基于T变换的降维观测器设计方法。要的一类观测器(Reduced-order state observer is very important dimension reduction based on T transform observer design method. To a class of observer)
- 2010-07-16 11:41:01下载
- 积分：1
-
fdct_wrapping_demo_denoise
用curvelet去除随机噪声。此为增强型的去除随机噪声。效果较好。(Remove the random noise using curvelet. This is the enhanced removal of random noise. Is better.)
- 2010-08-25 20:43:03下载
- 积分：1
-
continuous_daq_time_freq
Data Acquisition数据获取代码，主要从麦克风获取语音信号，然后real time plot输入信号的时域和频域波形图(Data Acquisition Data acquisition code, mainly for voice signal from the microphone, and then real time plot of the input signal in time domain and frequency domain waveform)
- 2010-10-14 04:33:26下载
- 积分：1
-
yichuansuanfa
说明： 遗传算法的matlab代码,适合数学建模的同学使用(Genetic algorithm matlab code, suitable for students to use mathematical modeling)
- 2008-09-09 09:12:26下载
- 积分：1
-
PCA
该源码使用主成分分析对原数据点进行分析。(Reshape the data points using the principal component analysis)
- 2012-05-01 15:05:50下载
- 积分：1
-
chap_3
matlab基础程序 便于初学者学习，matlab从入门到精通配套程序(matlab easy for beginners to learn the basis of the procedures, matlab package from entry to the master program)
- 2009-05-18 13:04:54下载
- 积分：1
-
power_seriesbranch
power_seriesbranch,功率电子领域matlab仿真文件，已经验证过，程序运行正常(
power_seriesbranch,Power electronics field matlab simulation file, has already been verified, the normal operating procedures)
- 2013-07-14 12:30:45下载
- 积分：1
-
radar_display_sim
本程序主要是对点迹数据进行滤波，形成航迹，并在雷达终端中进行显示。
本程序适用于阵列雷达，只显示一个阵面90度的范围。
由于通常雷达显示图以正北（显示器的正上方）为0度，与polar的零度不同，因此存在转化的问题。
(a program about radar display simulation)
- 2020-08-23 14:07:50下载
- 积分：1
-
modis_Spectral_response_function_fit
处理一定的遥感数据，可以自动读取，也可以将其生成。(Processing of remote sensing data can be automatically read, and can also be generated.)
- 2012-05-19 10:46:36下载
- 积分：1
-
雷达信号处理基本流程
去斜处理（宽带的匹配滤波）Stretch方法是针对线性调频信号而提出的， 其方法是将输入信号与参考信号 （经适当延迟的本振信号， 延迟量通常由窄带信号测距结果估计出） 混频 ，则每一个散射点就对应一个混频后的单频分量，对混频输出的信号进行 DFT 处理 ，即可获得目标的距离像，对参考信号的要求是应具有与输入信号相同的调频斜率。(dechirp matched filter
Stretch method is proposed for linear frequency modulation signal. It mixes the input signal with the reference signal (local oscillator signal with appropriate delay, the delay is usually estimated from the result of narrowband signal ranging). Then each scattering point corresponds to a single frequency component after mixing, and DFT is performed on the mixed-frequency output signal. The range profile of the target can be obtained by processing, and the reference signal is required to have the same frequency modulation slope as the input signal.)
- 2018-10-31 20:07:27下载
- 积分：1
