登录
首页 » Asm » 74HC164

74HC164

于 2012-09-27 发布 文件大小:1KB
0 168
下载积分: 1 下载次数: 3

代码说明:

  74164串行口转并行口芯片驱动模块,使用EMC系列单片机(74164 serial port to parallel port chip driver module, using EMC Series MCU)

文件列表:

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • CANOPEN
    PLC程序 施耐德PLC 通过CANOPEN控制3台伺服器(PLC Schneider PLC program control by CANOPEN 3 servers)
    2020-12-28 11:39:02下载
    积分:1
  • jidianqi
    程序是用stm32输出来的信号来控制继电器的开通与否,继而来控制电机的状态(Program is with stm32 output signal to control the opening of relay or not, and then to control the state of the motor )
    2013-09-11 14:23:27下载
    积分:1
  • PHD15A4100-01
    一段简单的幻影灯控制程序,新人可以拿来泡妹纸。(A simple piece of phantom lights control procedures can be used to soak the new sister paper.)
    2016-05-12 09:05:07下载
    积分:1
  • Proteus STM32 led
    在实现流水灯闪烁在proteus8.6使用的单片机是STM32F103R6(realize led SCM STM32F103R6 is used in Proteus 8.6 to realize pipeline lamp flickering.)
    2020-09-26 23:37:48下载
    积分:1
  • PMAC 中文手册(推荐详细)
    说明:  PMAC 中文手册(推荐详细)PMAC(可编程多轴运动控制器),是美国Delta Tau Data System 公司于推出的PC 机平台上的运动控制器,是一个完全开放的系统。(PMAC Chinese Manual (Recommended Details))
    2020-07-02 08:00:02下载
    积分:1
  • dingshiqi
    本程序采用C语言编程,利用proteus仿真实现定时器功能。(This program uses the C programming with proteus simulation clock function )
    2012-02-12 10:15:52下载
    积分:1
  • adaptive_PID_control_based_on_rbf_idnetification
    说明:  该算法是基于RBF神经网络整定的PID控制 分享一下,希望对大家有所帮助(The algorithm is based on the RBF neural network-tuning of PID control to share the hope of U.S. help)
    2020-12-15 21:09:13下载
    积分:1
  • lm75a
    飞利浦 lm75a i2c总线温度传感器 msp430驱动,内部包含f169i2c驱动 st7920画点函数等(Philips lm75a i2c-bus temperature sensor msp430 drive, internal drive st7920 picture contains f169i2c point function, etc.)
    2010-09-03 13:42:47下载
    积分:1
  • AD__c8051f
    基于c8051f单片机的内部模数转换模块程序,已封装,可以直接移植。。。(Based on the single chip microcomputer c8051f internal digital-to-analog conversion module program, already enclosed, can directly transplant...)
    2012-03-02 10:44:08下载
    积分:1
  • 3、系统定时器SysTick
    这是基于开发板LPC1114的源码程序,是用C语言编写,用于实现系统定时器的配置同时它也是一个完整的模板,可以在此基础上添加其他程序用于开发板的学习,是一个完整的模板,可直接使用。(This is a source code program based on the development board LPC1114. It is written in C language. It is used to realize the configuration of the system timer. At the same time, it is also a complete template. On this basis, other programs can be added for the learning of the development board. It is a complete template and can be used directly.)
    2020-06-22 17:20:02下载
    积分:1
  • 696518资源总数
  • 106161会员总数
  • 5今日下载