-
MATLAB4
code for ds cdma for matlab
- 2010-06-17 05:47:12下载
- 积分：1
-
Auto_Measure_system
利用ccs环境、MATLAB环境、DSP（TMS320F2812)、被测对象和Agilient网络分析仪E5071B，构建一个自动测量系统。
相信大部分人都知道基于NI公司的GPIB总线，可以实现自动测量，但NI公司的方案实在太昂贵，采用MATLAB能够大大降低成本。matlab与ccs之间基于RTDX协议进行数据交换，同时matlab基于TCP/IP协议与E5071B之间通信，源码说明如下：
（1）RTDX_ok目录：matlab7.0代码，包含了一个用GUI实现的界面和相关的具体代码，特别是在其中实现了SCPI语言来对仪器进行控制。
（2）TMS320F2812目录：包含ccs下的c代码，如果没有做过RTDX的应用，相信这个对你很有启发。(Use ccs environment, MATLAB environment, DSP (TMS320F2812), the measured object and Agilient network analyzer E5071B, construct an automatic measurement system. I believe that most people are aware NI' s GPIB-based bus, you can realize automatic measurement, but NI' s program is too expensive, the use of MATLAB can greatly reduce costs. ccs between matlab and RTDX protocol-based data exchange, while matlab based on TCP/IP protocol and communication between the E5071B, the source described as follows: (1) RTDX_ok directory: matlab7.0 code, contains a GUI implementation with the interface and specific code, especially in one of implementation of the SCPI language to control the apparatus. (2) TMS320F2812 directory: contains ccs of c code, if not done RTDX application, then I think it was very instructive for you.)
- 2009-03-27 21:43:54下载
- 积分：1
-
zhipai2
说明： 指派问题 微粒群PSO算法优化 带绘图 优化目标为工作质量(Assignment of particle swarm optimization PSO algorithm to optimize the drawing target with the quality of work)
- 2010-05-04 15:37:38下载
- 积分：1
-
type2_toolbox2
说明： 模糊二型,在matlab中的使用，附有说明论文 和例子(Fuzzy type 2, used in matlab, with explanatory papers and examples)
- 2020-11-13 15:39:43下载
- 积分：1
-
susanFDTD2D_PML
susan用PML边界条件编写的FDTD三维程序(susan with PML boundary conditions for the preparation of three-dimensional FDTD program)
- 2011-08-26 22:07:34下载
- 积分：1
-
lagelangrichengzifa
用拉格朗日乘子法解有约束优化问题的matlab程序。(Lagrange multiplier method for solving constrained optimization problems matlab program.)
- 2013-03-11 18:03:06下载
- 积分：1
-
Graphical
Graphical wpf programmation langage C#
- 2014-12-10 01:28:59下载
- 积分：1
-
GPS-single-point-velocity
通过matlab编程 进行GPS单点定位进行测速来反映所测地点晃动情况，采样数据1s（1Hz）
loadobsrinex.m 为接收机即所用GPS得到的监测数据，loadrinexGpsn.m GPS星历数据，single_v_main1.m是主程序，还有其他消除误差程序。(Through matlab programming for GPS single point positioning speed to reflect the test place moving situation, and the sampling data 1 s (1 hz)
Loadobsrinex. M for monitoring data, used the GPS receiver got loadrinexGpsn. M GPS ephemeris data, single_v_main1. M is the main program, and other procedures to eliminate error.
)
- 2014-11-14 14:36:46下载
- 积分：1
-
fcm
FCM聚类模型，通过load本地数据就可以聚类出分类。(FCM clustering model
)
- 2013-05-09 11:48:35下载
- 积分：1
-
parzen
这是parzen窗估计的典型例子，大家可以直接学习，是个不可多得的好材料。(This is a typical example of the estimated parzen window, we can learn, is a rare good material.)
- 2010-10-22 18:09:33下载
- 积分：1
