-
UsingSimulinkandStateflowInAutomotiveApplication
书中给出了九个典型的自动化设计例子。展示了如何用The MathWorks和其他仿真工具，比如Simulink和Stateflow建模，以此来使自动化控制系统的设计更加便利。(This book includes nine examples that represent typical design tasks of an automotive engineer. It
shows how The MathWorks modeling and simulation tools, Simulink® and Stateflow,TM facilitate
the design of automotive control systems. Each example explains the principles of the physical situation,
and presents the equations that represent the system. The examples show how to proceed
from the physical equations to the Simulink block diagram. Once the Simulink model has been
completed, we run the simulation, analyze the results, and draw conclusions from the study.)
- 2009-09-11 15:37:36下载
- 积分：1
-
gngauss
generate the gaussian noise
- 2009-04-18 16:31:09下载
- 积分：1
-
Deploy-Nodes
节点定位，仿真锚节点和未知节点的定位，用不同的符号表示。(Deploy Nodes………………………………)
- 2012-04-24 12:15:56下载
- 积分：1
-
nhandangtienghuytsao
detection voice used matlab.
detec voice piano,organ...
- 2015-02-16 00:14:21下载
- 积分：1
-
基于有限差分法的二维边值问题的数值分析
1. 在matlab中分析基于分离变量法的解析解；
2. 利用简单迭代法求解，与解析法结论对比，分析求解结果的精确度。分析过程至少包括：在网格尺寸为0.1 m和1 m两种条件下，两次迭代差值最大为10-10时的分析结论；
3. 利用超松弛迭代法分析，选择松弛因子，分析其对收敛速度（即迭代次数）的影响，并确定最优值。分析过程至少包括：在网格尺寸为0.1和1两种条件下，两次迭代差值最大为10-10时，迭代次数随松弛因子的变化，得到对应的最优松弛因子，与经验值（课本165页式子3.7.15）进行对比。(1. Analyze the analytical solution based on the separation variable method in matlab.
2. Using a simple iterative method to solve, compared with the results of the analytical method to analyze the accuracy of the solution. The analysis process at least includes the following conclusions: when the mesh size is 0.1m and 1m, the maximum difference between two iterations is 10-10.
3. Analyze using the relaxation relaxation iteration method, select the relaxation factor, analyze its influence on the convergence speed (ie the number of iterations), and determine the optimal value. The analysis process at least includes the following: when the mesh size is 0.1 and 1 and the maximum difference between two iterations is 10-10, the number of iterations varies with the relaxation factor, and the corresponding optimal relaxation factor and empirical value are obtained ( Textbook 165 pages (3.7.15) for comparison.)
- 2020-07-28 18:48:39下载
- 积分：1
-
nmf
说明： 这是对于矩阵分解里面，最新出现的一种新的算法：非负矩阵分解的程序(This is the decomposition of the matrix inside, emerging a new algorithm: the procedure of non-negative matrix factorization)
- 2011-04-14 15:14:27下载
- 积分：1
-
LDA
判別分析法（discriminant analysis），是在已知的分類之下，一旦遇到有新的樣本時，可以利用此法選定一判別標準，以判定如何該將新樣本放置於那個族群中。
(Discriminant analysis (discriminant analysis), under the classification of the known event of the new sample, the method has been applied to select a criterion to determine how the new sample is placed in that population.)
- 2012-04-26 14:01:52下载
- 积分：1
-
minnorm
现代信号谱分析 minnorm MATLAB 算法例程(spectral analysis of signals)
- 2012-05-11 14:28:35下载
- 积分：1
-
synseis_press
matlab code for seismogram generation
- 2014-12-12 15:53:16下载
- 积分：1
-
MODLEACH
MODLEACH is a protocol developed for wireless sensor networks and is a routing protocol
- 2013-12-17 18:49:42下载
- 积分：1
