-
keypad_matrix
this a keypad matrix applicable for ZDSII
- 2013-12-23 00:42:44下载
- 积分：1
-
MSP430-C
学习msp430系列单片机很好的编程材料，里面介绍了实用C 语言程序设计技巧。(Learn good programming msp430 MCU material, which describes a practical C language programming skills.)
- 2013-05-30 23:21:27下载
- 积分：1
-
TEA5767
tea5767收音机原理图，mcu是STC90C52属51系列单片机,原码在网上可搜。(TEA5767 RADIO SCH，MCU IS STC90C52 IN
SYSTEM，SOURCE PROGRAM WEB SEARCH )
- 2013-07-14 11:57:49下载
- 积分：1
-
Serial-communication
Matlab环境下PC机与单片机的串行通信及数据处理(Serial communication and data processing Matlab environment PC and SCM)
- 2013-12-11 13:50:53下载
- 积分：1
-
MicroprocessorDriveDM9000
网上有许多关于DM9000网卡芯片的介绍，然而这些介绍大多是关于Linux或WinCE下的驱动程序或移植，很少有介绍单片机驱动DM9000的例子。本文详细介绍了调试DM9000E的过程，仅供参考。(There are many online card chip on the DM9000 introduction, however, most of these presentations are on Linux or WinCE driver or under the transplantation, very few examples of introduced Microprocessor DM9000. This paper describes the process of debugging DM9000E for reference purposes only.)
- 2010-07-17 00:13:28下载
- 积分：1
-
speed
采用霍尔传感器3020T,根据霍尔效应原理,在电机转轴边沿上放一永久磁钢,转轴附近放一个别3020T,当转轴旋转时,受磁钢的影响,霍地尔器件输出脉冲信号,送至单片机中断引脚,转速计数加1,单片机内部产生5s的定时,计算出1分钟的转速,送至显示单元,(Using Hall sensors 3020T, according to Hall-effect principle, the motor shaft of a permanent magnet placed on the edge, do not put a shaft near the 3020T, when the shaft rotates by magnet effect, HUO Di Seoul device output pulse signal, sent to microcontroller interrupt pin, speed count plus 1, the microcontroller internally generated timing 5s to calculate the speed of 1 minute, sent to the display unit,)
- 2010-12-18 22:35:31下载
- 积分：1
-
oscilloscope_design
说明： 虚拟示波器的设计实线 对数据采集有参考价值(labview teaching)
- 2009-08-03 11:21:37下载
- 积分：1
-
timer
基于单片机实现定时器的应用,用c语言编写的.(Based on the single chip microcomputer application of the timer, written in c.)
- 2012-05-07 21:25:59下载
- 积分：1
-
15.5
带字库的12864仿真软件学习带电路图和仿真软件。(12864 with a font with a circuit simulation software and simulation software to learn.)
- 2013-11-01 23:15:48下载
- 积分：1
-
template
stm32配置模板，了解 STM32 的标准库文件之后，我们就可以使用它来建立工程了，因为用库新建工程的步骤较多，我们一般是使用库建立一个空的工程，作为工程模板。以后直接复制一份工程模板，在它之上进行开发(Once you understand the standard library file for STM32, we can use it to build the project because of the new library build
There are more steps, and we usually use the library to build an empty project as an engineering template. Direct a copy of the work later
The process template is developed on top of it)
- 2017-09-17 13:40:25下载
- 积分：1
