登录
首页 » PDF » Amouzesh_Matlab

Amouzesh_Matlab

于 2010-07-29 发布 文件大小:2828KB
0 230
下载积分: 1 下载次数: 1

代码说明:

  lerarning matlab simply with math

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • power_steppermotor
    power_steppermotor.rar,功率电子领域matlab仿真文件,已经验证过,程序运行正常(power_steppermotor.rar,Power electronics field matlab simulation file, has already been verified, the normal operating procedures)
    2013-07-14 12:41:58下载
    积分:1
  • RFnuaCopy
    multi device antenna in matlab
    2013-10-21 01:12:35下载
    积分:1
  • GAN
    MATLAB中GAN网络实现,包含minist测试数据(GAN realization on MATLAB)
    2021-03-15 11:49:22下载
    积分:1
  • fruit-
    (MATLAB)果蝇优化SVR程序具体案例分析((MATLAB) fruit fly optimization SVR program specific case analysis)
    2016-04-20 11:42:28下载
    积分:1
  • RMA1
    条带式SAR的正侧视仿真,采用RMA算法进行仿真(Striped positive side-looking SAR simulation, the simulation using RMA algorithm)
    2010-07-25 10:50:37下载
    积分:1
  • seg
    matlab图像分割识别算法。读入车牌可识别出车牌号码并输出。(matlab image segment algorithm. read in a car license plate can output the number in the plate.)
    2009-11-24 13:21:24下载
    积分:1
  • 7
    说明:  双曲型方程组的理论基础,包括守恒型方程组、非守恒型方程组的理论基础(The theory of hyperbolic basis, including the conservation equations, equations of non-conservative theory)
    2011-03-19 10:09:52下载
    积分:1
  • duffing
    一个duffing模型,一个噪声模型,一篇duffing检测原理,。可检测不同频率的待测信号(a duffing model, a noise model, a duffing detection principle)
    2019-05-18 17:45:02下载
    积分:1
  • Articulatedvehicle6freedomlinearmodel
    建立了铰接车六自由度线性模型,用于分析半挂汽车等铰接列车的动力学分析(Six degrees of freedom to establish a linear model articulated truck, trailer and automobile for the analysis of the dynamics of articulated trains)
    2010-10-08 11:00:20下载
    积分:1
  • Link-a-System-Level-OFDM-Simulator
    针对OFDM系统,分成链路级仿真和系统级仿真两个部分。为了降低系统级仿真的复杂度,采用链路级仿真的部分结果。(It contains mainly two parts, i.e. link-level simulator and system-level simulator. Link-level simulator focus on a single-cell single-user scenario, where signal is transmitted from tx, and estimated at rx. Comparing the difference in tx/rx signal, the error rate can be found out. The output of the link-level simulator is the BLER/BER vs. SNR mapping table, that can be used for the system-level simulation. System-level simulator focus on a multi-cell multi-user scenario. For the sake of simplicity, it takes the mapping table aquired in the link-level simulation, measure the actural SNR, and finds the corresponding error rate. Link-level simulator support SISO, 1 by x MRC, 2 by 1 STBC/SFBC, 2 by 2 Alamouti, x by 1 Antenna selection, x by y antenna selection. System-level simulator, currently support only SISO and 1 by 2 MRC. To start with, go into the folder sys_link_simu, and excute the following commond from matlab: sys_link_simu_func(a,b) where a is the link ada)
    2011-08-09 11:00:53下载
    积分:1
  • 696516资源总数
  • 106459会员总数
  • 0今日下载