-
matlab_vc_mex
混合编程方法,便于VC++与matlab进行混合编程(matlab and vc++ mex)
- 2009-09-27 18:44:23下载
- 积分:1
-
topologyopt
A 99 LINE TOPOLOGY OPTIMIZATION CODE BY OLE SIGMUND
- 2009-10-01 17:08:13下载
- 积分:1
-
OFDM-xianfu
说明: 在OFDM系统中,采用限幅法降低峰均功率比,该文件包括了流程图和matlab源码(In OFDM system, using limiting PAPR reduction method, the document includes flow charts and source code matlab)
- 2021-02-21 23:29:41下载
- 积分:1
-
stiffODE
stiff ODE solver for set of equations
- 2011-08-31 08:49:30下载
- 积分:1
-
subtry
分析声音波长频率,通过对声音的分析,以达到识别声音的效果(Analyze sound wavelength frequency, through the analysis of the sound to identify the effect of the sound)
- 2012-11-14 21:56:59下载
- 积分:1
-
00993274
Matrix Converter Commutation Strategies With and
Without Explicit Input Voltage Sign Measurement
- 2014-01-24 01:53:58下载
- 积分:1
-
spectral_clustering_cogs118b-master
1. 按照式计算相似性矩阵
2. 排除自身的相似度
3. 按照式计算归一化矩阵
4. 按照式计算归一化拉普拉斯图矩阵L
5. 计算L的特征向量,将前个特征值最大的向量按列放置成一个矩阵,即依次为前个特征值最大的特征向量
6. 归一化X形成矩阵Y
7. 对矩阵Y按每行为一个数据点,进行k-means聚类,第行所属的类就是原来所属的类。(1. similarity matrix based on formula computation
2. rule out your own similarity.
3. normalized matrix based on formula computation
4. normalized formula Laplasse matrix L according to formula.
5. Calculate the eigenvectors of L. Place the vectors with the largest eigenvalues in columns into a matrix, that is, the eigenvectors with the largest eigenvalues in turn.
6. normalized X formation matrix Y
7. K-means clustering is applied to matrix Y according to one data point per behavior. The first row belongs to the original class.)
- 2018-11-16 09:14:48下载
- 积分:1
-
DSP
任务:
1) 借助MATLAB画出误差性能曲面和误差性能曲面的等值曲线(参考PPT2.1第17页的两幅图);
2) 写出最陡下降法以及LMS算法的计算公式(取 );
3) 用MATLAB产生方差为0.05, 均值为0白噪音S(n),并画出某次采样得到的波形(即产生任意一个噪声随机序列);
4) 根据 2)中的公式,并利用 3)中产生的S(n),在 1)中的误差性能曲面的等值曲线上叠加画出采用最陡下降法以及LMS法时H(n)的在叠代过程中的轨迹曲线(参考PPT2.1第17页的右下图的曲线1和曲线2)。
5)用MATLAB计算并画出LMS法时 随时间n的变化曲线(对应S(n)的某一次的一次实现)和e(n)波形;
注意:某一次实现的结果并不能从统计的角度反映实验的结果 的正确性,为得到具有统计特性的实验结果,可用足够多次的 实验结果的平均值作为实验的结果。用MATLAB计算并画出 采用LMS法时,J(n)的100次实验结果的平均值随时间n的变 化曲线(即 生成随机噪声信号并计算结果,重复执行100次, 求平均结果)。
6)在 1)中的误差性能曲面的等值曲线上,叠加画出采用LMS法得到的100次实验中的H(n)的平均值的轨迹曲线;
(Task:
1 ) Draw with MATLAB error performance surface and surface contour error performance curve ( refer PPT2.1 two chart on page 17 )
2 ) Write the steepest descent method and the LMS algorithm formula ( take )
3 ) Using MATLAB to generate variance of 0.05 with a mean of 0 white noise S (n), and draw a particular sampling waveform ( ie, any noise generated random sequence )
4 ) based on 2 ) of the formula , and use 3 ) generated in S (n), in a ) the error performance curves superimposed on the surface contour plot using the steepest descent method and the LMS method when H (n) the iterative process in the trajectory curve ( refer PPT2.1 page 17 bottom right of the curves 1 and 2 ) .
5 ) using MATLAB LMS method is used calculate and draw the curve with time n (corresponding to S (n) of a first implementation of a ) and e (n) waveform
Note : in a first implementation of the results are not reflected from a statistical point of view of accuracy of the experimental results ,)
- 2013-11-08 20:09:06下载
- 积分:1
-
identification
说明: 用刚度文件FEM,对模型进行不同单元的损伤识别,同时得到损伤程度(The stiffness file FEM is used to identify the damage of different elements of the model, and the damage degree is obtained at the same time.)
- 2019-02-26 15:46:11下载
- 积分:1
-
F16FlightControlSimulation
F16飞行控制仿真程序,针对F16战斗机做的飞行控制仿真(F16 flight control simulation program, to do for the F16 fighter flight control simulation)
- 2011-10-17 10:09:00下载
- 积分:1