登录
首页 » PDF » P10sch

P10sch

于 2015-01-09 发布 文件大小:454KB
0 56
下载积分: 1 下载次数: 53

代码说明:

  P10 LED matrix module schematic dỉ gram (P10 单元板电路图)

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • 超声波
    使用超声波模块测距,测距范围 10cm--1..2m(Using ultrasonic module to measure distance, ranging range is 10cm-1.2m.)
    2020-06-18 10:00:01下载
    积分:1
  • 3
    说明:  红外编码发生器程序 自己编写 调试成功 大家可以看看(IR code generator program written to debug their success we can see)
    2010-08-23 16:57:21下载
    积分:1
  • 液位传感器TTL输出程序
    说明:  超过液位后警示灯动作,提示或警告液面已经到达警示位(Warning lamp action after exceeding liquid level)
    2020-06-25 09:40:02下载
    积分:1
  • LabVIEW_PID_Design_Source_Code
    附件为LabVIEW的vi程序和说明文档。描述:利用LabVIEW2012设计PID控制器,利用PID工具包,在LabVIEW仿真工具包中的控件与仿真循环中搭建PID控制器,并实现了闭环控制系统波形图的显示。(Attachments are the LabVIEW vi program and the documentation for PID controller design. The program includes the PID controller constructing and the closed-loop system output display.)
    2013-12-13 14:43:19下载
    积分:1
  • stm8--BLDC-pcb-sch-
    stm8单片机实现了控制bldc轮毂电机的控制,用了6个mos管,采用六部控制,里面有 pcb sch 和程序,可以用此资料改装成电动自平衡独轮车(Stm8 microcontroller realized control BLDC hub motor control, with 6 mos tube, using six control with Sch and PCB program, this information is converted into electric self balancing unicycle)
    2021-03-16 15:59:22下载
    积分:1
  • victoria_447
    something else lox lox1
    2018-02-22 05:43:36下载
    积分:1
  • BecomeAGoodSpeaker
    CAN CAN总线 空调智能节电的应用,汇编语言(CAN CAN intelligent saving air-conditioning applications, assembly language)
    2007-06-03 12:14:59下载
    积分:1
  • HDG12864F-3LCDDriver
    HDG12864F-3的液晶驱动,有Protues硬件仿真图,方便初学者参考(HDG12864F-3 LCD driver, a Protues hardware simulation map, easy reference for beginners)
    2010-08-13 09:43:14下载
    积分:1
  • rs485
    通过RS485端口不停地发送数据0xaa用示波器观察RS485端口A、B信号线上的波形或者用RS485接收器接收发送的字符。(Through the RS485 port to send data continuously 0xaa observed with an oscilloscope RS485 ports A, B signal waveforms or use the RS485 line receiver sends characters.)
    2013-08-02 08:59:55下载
    积分:1
  • STM32_ADXL345_IIC
    说明:  我使用的是F103VET6,软件IIC控制,改引脚配置后可方便移植。 SDL连接PB6、SDA连接PB7、CS连接高电平,SDO连接高电平的话模块的写地址为0x3A、读地址为0x3B··· ···(I use F103VET6, software IIC control, pin configuration can be easily transplanted. SDL connects PB6, SDA connects PB7, CS connects high level. SDO connects high level telephone module with write address of 0x3A and read address of 0x3B.)
    2020-07-01 19:00:02下载
    积分:1
  • 696522资源总数
  • 104022会员总数
  • 48今日下载