-
machine-asynchrone
dynamic model of asynchrones machine
- 2014-12-03 21:28:45下载
- 积分：1
-
case_study_3
关于风电最大功率跟踪控制的simulink仿真，比较了传统的控制方法和信号搜索方法。(matelab About Wind Power Maximum Power Tracking Control of simulink simulation to compare the traditional control method and signal search method.
)
- 2014-02-16 20:32:04下载
- 积分：1
-
findpks_MinMax
Find peaks in signal. Look for local maxima and minima. In the window of search find the maximum maxima and the minimum minuma. Return two values which are the maximum and the minimum local maximas
- 2010-06-18 00:46:33下载
- 积分：1
-
tpc
说明： MATLAB仿真IS-95开环闭环功率控制
(MATLAB simulation IS-95 open-loop power control loop)
- 2006-04-30 10:51:53下载
- 积分：1
-
hunhebianma
VC + + 与MATLAB 混合编程,可以将VC 优秀的可视化编程能力和MATLAB 强大的计算能力结合起来。
分析了C 语言与MATLAB7. x 在接口的特点,详细介绍了VC + + 6. 0 与MATLAB7. x 混合编程的三种方法: MATLAB
引擎、MATLAB 编译器和MATLAB COM 编译器(VC++ Mixed with MATLAB programming, can be excellent VC Visualization MATLAB programming capacity and computing power together. Analysis of the C language and MATLAB7. X in the interface characteristics described in detail VC++ 6. 0 and MATLAB7. X mixed programming in three ways: MATLAB engine, MATLAB Compiler and MATLAB COM compiler)
- 2008-12-23 19:32:39下载
- 积分：1
-
CHAPTER2
Communition MATLAB (Proakis)书中的源程序，很不错(Communition MATLAB (Proakis) source book, very good)
- 2008-05-16 18:00:45下载
- 积分：1
-
KNN3
说明： matlab环境下 实现的3类分类的KNN算法(KNN algorithm to classify three classes developed by matlab)
- 2010-04-15 20:45:10下载
- 积分：1
-
zy
说明： （本科生课程设计）主要实现的功能是设计一个恒压恒频正弦波逆变电源，具体参数如下：单相交流输入220V/50Hz，输出单相交流电压110V/50Hz,THD<5 ,负载为一般的阻感负载，功率1500W。利用matlab中simulink实现仿真功能。(The main functions of the (undergraduate curriculum design) is designing a constant voltage constant frequency sine wave inverter, specific parameters are as follows: single-phase AC input 220V/50Hz, output single-phase AC voltage 110V/50Hz, THD < 5 load general resistance inductive load, power 1500W. Matlab in simulink simulation capabilities.)
- 2013-01-29 09:45:19下载
- 积分：1
-
square2dTM_mst
根据平面波展开法绘制的二维光子晶体能带图，包括TM和TE波两种模式(2d photonic crytal band structure)
- 2013-03-18 14:12:42下载
- 积分：1
-
Boost_Converter
说明： 升压转换器是一种DC / DC电源转换器，可将电压从其输入（源）升至其输出（负载）。在连续导通模式下（流经电感的电流永远不会降为零），升压转换器的理论传递函数为：
占空比在哪里0.5
在此示例中，转换器从250 V电源馈送RC负载，并且PWM频率设置为31 kHz。
模拟
运行仿真并观察示波器上的波形。确认负载电压（Vout）的平均值非常接近理论值：Vout = 250 /（1- 0.5）= 500V。(A boost converter is a DC/DC power converter which steps up voltage from its input (source) to its output (load). In continuous conduction mode (current through the inductor never falls to zero), the theoretical transfer function of the boost converter is:
where is the duty cycle.0.5
In this example, the converter is feeding an RC load from a 250 V source and the PWM frequency is set to 31 kHz.
Simulation
Run the simulation and observe waveforms on Scope. Verify that the mean value of the load voltage (Vout) is very close to the theoretical value of: Vout = 250 / (1 - 0.5) = 500 V.)
- 2020-03-22 20:41:56下载
- 积分：1
