登录
首页 » matlab » qq1

qq1

于 2011-12-05 发布 文件大小:1KB
0 187
下载积分: 1 下载次数: 17

代码说明:

  简单的matlab图像处理程序 以RGB颜色模型进行图像检测并包括颜色检测后腐蚀膨胀等滤波处理(Simple matlab image processing procedures to RGB color model testing and including color image after testing corrosion expansion filtering processing, etc )

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • FastMatrixInversionAlgorithm
    矩阵快速求逆算法,算法比较简单,使用效果比较明显(Fast matrix inversion algorithm)
    2010-10-24 11:05:56下载
    积分:1
  • tongjifx333
    此程序为统计分析中常见的统计量的matlab程序,有详细注释.(the progroms is very good)
    2013-07-31 11:18:07下载
    积分:1
  • TOOLBOX_calib
    基于matlab的摄像机标定代码,精度很高,可直接用于程序。(Camera Calibration Based on matlab code, high precision, can be used for procedures.)
    2010-05-31 14:50:07下载
    积分:1
  • TS_TSP
    运用禁忌搜索算法解决旅行商问题TSP的程序代码,简单实用(yunyon gjin jisou suosaulv xign shang)
    2015-01-15 11:24:28下载
    积分:1
  • chap4
    .已知某炉温控制系统,要求温度保持在600℃恒定,针对该控制系统有以下控制经验: (1)若炉温低于600℃,则升压,低的越多升压越高; (2)若炉温高于600℃,则降压,高得越多降压越低; (3)若炉温等于600℃,则保持电压不变。 设模糊控制器为一维控制器,输入语言变量为误差,输出为控制电压。输入输出变量的量化等级为7级,取5个模糊集,试设计隶属度函数误差变化划分表,控制电压变化划分表和模糊控制规则表。 (Known for a temperature control system that requires a constant temperature is maintained at 600 ℃, the following control experience for the control system: (1) If the furnace temperature is below 600 ℃, the step-up, the more the higher the lower the boost (2) if the furnace temperature is higher than 600 ℃, the blood pressure, high blood pressure, the lower the more (3) If the furnace temperature is equal to 600 ℃, then keep the voltage constant. Set of fuzzy controller for one-dimensional controller, input linguistic variables for error, the output control voltage. Input and output variables of quantization levels for seven, take five fuzzy sets, membership function test design error variance divided table, partition table and the control voltage variation fuzzy control rule table.)
    2015-04-10 21:53:18下载
    积分:1
  • trial_code
    This is the code for contourlet transform using 9-7 bior filters and 23-45 filters..
    2011-02-11 19:25:38下载
    积分:1
  • matlab
    数字控制系统仿真与综合应用:设控制对象为 W1=10/s(1+0.1s)(1+0.05s),采样周期T=0.2s。 (1)采用零阶保持器,将W1(s)转换成W1(z),串接一个计算机调节模型D(z)组成一个典型的数字反馈系统。分别用仿真方法得到系统在单位阶跃输入作用下的响应和系统在单位速度输入时的输出响应。 (Digital control system simulation and comprehensive application: set control object for W1 = 10/s (1+ 0.1 s) (1+ 0.05 s), the sampling period T = 0.2 s. (1) the zero order keep device, will W1 (s) convert W1 (z), the combination of a computer adjusting model D (z) composed of a typical digital feedback system. The simulation method were used to get in the unit step input system under the action of response and system in the unit of output response speed input. )
    2012-04-19 14:38:25下载
    积分:1
  • Matlab-simulation-model-of-dc-dc-converters
    This matlab file explains the operation of Boost and buckboost converter with open loop as well as closed loop operation for voltage regulation and power factor improvement.
    2014-09-03 14:26:21下载
    积分:1
  • ihDemo
    说明:  MATLab 信息隐藏实验特别好 MATLab very good information hiding experiment(MATLab very good information hiding experiment MATLab very good information hiding experiment)
    2013-12-06 17:02:54下载
    积分:1
  • denoise_julei
    利用聚类算法和小波分析进行声发射信号的阈值去噪 (The use of clustering algorithms and thresholding wavelet analysis of acoustic emission signals)
    2014-01-06 09:54:50下载
    积分:1
  • 696518资源总数
  • 106215会员总数
  • 5今日下载