登录
首页 » matlab » queueM

queueM

于 2012-10-18 发布 文件大小:1KB
0 202
下载积分: 1 下载次数: 25

代码说明:

  使用matlab编写的排队算法,队列长度为m(Queuing algorithm, using matlab queue length m)

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • CRB
    均匀线阵的CRB曲线,适用于阵列信号处理问题(CRB curve of the uniform linear array)
    2012-06-15 10:51:38下载
    积分:1
  • tiaopin
    说明:  跳频通信仿真论文,大家看一下啊,好不容易找到的(Frequency-hopping communication simulation paper, we look at, ah, hard-won)
    2010-04-21 09:33:20下载
    积分:1
  • BPSK
    simulink仿真框图来实现BPSK调制(simulation simulink block diagram to realize BPSK modulation)
    2007-10-11 10:28:10下载
    积分:1
  • l1svtool
    this is matlab code to solve various convex problem!!!
    2012-05-31 16:13:53下载
    积分:1
  • exam53
    阻尼系数的非线性估计,用于估计伴随未知定值阻尼和已知重力情况下的垂直系统(Nonlinear estimation of damping coefficient;This would be an appropriate model for a VERTICAL mass-spring system with UNKNOWN constant damping and known gravity forcing.)
    2009-12-23 19:57:00下载
    积分:1
  • changguichaoliu
    常规潮流,我自己编写的,非常好用的潮流计算程序(Conventional trend, I write, very handy flow calculation program )
    2012-04-22 19:31:22下载
    积分:1
  • FC
    说明:  简单的模糊控制器(Fuzzy Controller)的simulink仿真!(The simulation of fuzzy logic controller (Fuzzy Controller)!)
    2020-11-09 18:49:47下载
    积分:1
  • pcm
    PCM simulink matlab example
    2010-02-17 18:46:03下载
    积分:1
  • xiaobosuanfa
    采样频率 fs=10000 轴承外环故障信号 fid=fopen( bearingout.dat , r ) 故障 N=1024 xdata=fread(fid,N, int16 ) fclose(fid) xdata=(xdata-mean(xdata))/std(xdata,1) 时域波形 figure(1) plot(1:N,xdata) xlabel( 时间 t/n ) ylabel( 电压 V/v ) db10小波进行4层分解 一维小波分解 [c,l] = wavedec(xdata,4, db10 ) 重构第1~4层细节信号 d4 = wrcoef( d ,c,l, db10 ,4) d3 = wrcoef( d ,c,l, db10 ,3) d2 = wrcoef( d ,c,l, db10 ,2) d1 = wrcoef( d ,c,l, db10 ,1) ( Sampling frequency fs = 10000 bearing outer ring fault signal fid = fopen (' bearingout.dat' , ' r' ) failure N = 1024 xdata = fread (fid, N, ' int16' ) fclose (fid ) xdata = (xdata-mean (xdata))/std (xdata, 1) time-domain waveform figure (1) plot (1: N, xdata) xlabel (' Time t/n' ) ylabel ( ' voltage V/v' ) db10 wavelet decomposition 4 layer one-dimensional wavelet decomposition [c, l] = wavedec (xdata, 4, ' db10' ) 1 ~ 4 reconstructed detail signal d4 = wrcoef (' d' , c, l, ' db10' , 4) d3 = wrcoef (' d' , c, l, ' db10' , 3) d2 = wrcoef (' d' , c, l, ' db10' , 2) d1 = wrcoef (' d' , c, l, ' db10' , 1) )
    2011-05-21 16:48:36下载
    积分:1
  • cmcm交叉模型交叉模态方法
    本程序可以进行有限元模型修正和结构损伤识别,优点是基本解决了测量信息有限的问题。(This program can perform finite element model correction and structural damage identification. The advantage is that the problem of limited measurement information is basically solved.)
    2018-08-19 10:43:03下载
    积分:1
  • 696516资源总数
  • 106554会员总数
  • 12今日下载