-
hjghjgjghg
单片机课程设计
电子压力器的工作原理
电子压力器由压力传感器,A/D转换器,数码显示等组成。
(MCU Design pressure of the working principle electronic pressure is controlled by electronic pressure sensor, A/D converter, digital display and other components.)
- 2011-05-27 16:47:18下载
- 积分:1
-
电表驱动ATT7022待测试版本 ATT7022 stm32f103
说明: 电表驱动ATT7022待测试版本,需要的请测试测试。(Watt-hour meter drive ATT7022 to be tested version, need to be tested.)
- 2021-04-14 10:28:55下载
- 积分:1
-
JINGTAI
51单片机静态数码管显示51单片机静态数码管显示(sfasdasdasd )
- 2013-07-28 10:53:32下载
- 积分:1
-
AT89S51demo
说明: AT89S51demo代码,方便快速开发(AT89S51demo Code, Convenient and Rapid Development)
- 2020-06-19 06:20:01下载
- 积分:1
-
HMC5883L
HMC5883L测试程序,MCU为AT89S52,经测试可用(HMC5883L testing procedures, MCU for AT89S52, have been tested)
- 2014-03-06 15:24:51下载
- 积分:1
-
给单片机初学者的43个实验
说明: 入门教程,给单片机初学者43个实验教程,(Introductory tutorials, 43 experimental tutorials for beginners of microcontroller.)
- 2020-06-24 12:20:02下载
- 积分:1
-
步进电机
编制MCS-51程序使步进电机按照规定的转速和方向进行旋转,并将已转动的步数显示在数码管上。
步进电机的转速分为两档,当按下S1开关时,加速旋转,速度从10转/分加速到60转/分。当松开开关时,减速旋转,速度恢复为10转/分。当按下S2开关时,按照逆时针旋转;当松开时,按照顺时针旋转。
本程序要求使用定时器中断来实现,不准使用程序延时的方式。(The MCS-51 program is programmed to rotate the stepper motor according to the specified speed and direction, and the number of steps that have been rotated is displayed on the digital tube.
Stepper motor speed is divided into two gears. When the S1 switch is pressed, the speed is accelerated from 10 rpm to 60 rpm. When the switch is loosened, the speed will be reduced to 10 rpm. When pressing the S2 switch, rotate counterclockwise; when loosening, rotate clockwise.
This procedure requires the use of timer interrupt to achieve, do not use the way of program delay.)
- 2020-06-16 09:40:02下载
- 积分:1
-
4线步进电机控制
步进电机控制,采用4线程得方式,C语言编写,亲测可用(Stepper motor control, using 4 threads, C language, pro-test available)
- 2019-04-19 17:00:20下载
- 积分:1
-
1_LED
说明: stm8 点灯工程,已经编译通过,使用的标准库(STM 8-point lamp project)
- 2020-06-16 20:20:01下载
- 积分:1
-
1、LED灯
基于51单片机的led源程序,常见问题解决方法
:
LED不亮的:
1. 请您检查排线是否插好!
2. 换根排线试试。(Led Source Program Based on 51 Single Chip Microcomputer,Solutions to Common Problems:LED is not bright:
1.Please check whether the cable is plugged in properly.
2.Try changing the cable.)
- 2020-06-20 17:40:02下载
- 积分:1