登录
首页 » matlab » td1

td1

于 2013-11-08 发布 文件大小:1KB
0 159
下载积分: 1 下载次数: 16

代码说明:

  tdoa. wsn. time difference of arrival simulation.

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • bk02ppt-3217
    MATLAB及在电子信息课程中的应用,感觉很有用.(MATLAB and in the course of electronic information, I feel useful)
    2010-08-07 13:02:37下载
    积分:1
  • AMMC
    Matlab 视频去隔行代码AMCC法,效果很好(Matlab code Deinterlacing)
    2013-09-02 19:48:05下载
    积分:1
  • fungsi_4
    Function for scan type 4
    2010-01-13 22:02:31下载
    积分:1
  • pll
    基于simulink的频率合成器实现,可实现小数分频(Simulink-based frequency synthesizer implemented to achieve fractional)
    2011-05-12 12:12:49下载
    积分:1
  • Codes
    calcul du champ rayonné par l antenne
    2012-05-10 21:19:50下载
    积分:1
  • Atmosphere
    Atmosphere model for 200km
    2012-08-27 04:42:24下载
    积分:1
  • simulink_tutorial
    matlab simulnk tutorial for engineers
    2011-09-01 20:07:00下载
    积分:1
  • IIR
    用MATLAB下面的simulink库里的dsp builder搭建了一个图形化的iir滤波器模型(Using MATLAB simulink library following the dsp builder to build a graphical model of iir filter)
    2020-12-02 20:09:25下载
    积分:1
  • chengxu
    小波变换进行变速箱故障诊断 首先将s1和s2信号时域谱(s1代表维修前的振动信号,s2代表维修后的振动信号),画出来进行对比,会发现s1信号的振动幅值会比较高;然后对s1和s2分别进行小波分解并画出各层的时域谱,只对比s1和s2分后的最高时域谱,s2更加的具有周期性,且幅值较小,s2周期性不够明显,且振动过于密集。分析完时域谱后开始分析频谱,首先对原信号s1和s2fft转换,得到频谱图,如图,然后再对小波分析后高频部分进行fft转换,做出频谱图。对比后我们发现,在f 2375HZ出(也就是齿轮的啮合频率),s1信号频谱幅值会有急剧的升高,然后,其谐波的幅值也会增大。所以可以推断出该维修前的增速箱的齿轮可能出现问题。(Gearbox fault diagnosis based on wavelet transform s1 and s2 first time domain signal spectrum (s1 behalf of the vibration signal before maintenance, vibration signal s2 representative of repaired), drawn comparison, you will find a signal s1 vibration amplitude will be higher then s1 and s2 respectively wavelet decomposition and draw the layers of time-domain spectrum to only a maximum time domain spectroscopy s1 and s2 points after, s2 is more cyclical and smaller magnitude, s2 cyclical enough obviously, and the vibration is too dense. End domain spectral analysis after the beginning of the spectrum analysis, the first of the original signal s1 and s2fft conversion to give the spectrum, as shown, and then after the high frequency part of wavelet analysis fft transformation to make spectrum. We found that after the comparison, at f 2375HZ out (i.e. the gear mesh frequency), there will be a sharp increase in the amplitude spectrum of the signal s1, and then, the amplitude of the ha)
    2017-01-17 19:18:02下载
    积分:1
  • CRC
    通过学习CRC编码原理,本部分建立了SIMULINk模型,实现了CRC编译码。(in this part we build the simulink modol of the encoded and decoded of CRC.we can more understand the code)
    2011-01-01 22:33:07下载
    积分:1
  • 696518资源总数
  • 106161会员总数
  • 5今日下载