-
yibiao1
简单使用modbus实现仪表的数据读取，实现串口通讯(Simple to use modbus to achieve the instrument' s data to read, and serial communication)
- 2020-08-02 19:08:35下载
- 积分：1
-
Multiple Connections - Client 2
LabVIEW客户端第二界面，是实现LabVIEW TCP通信的客户端第二个界面。(The LabVIEW client second interface is the second interface of the LabVIEW TCP communication client.)
- 2018-05-08 19:11:36下载
- 积分：1
-
NewportESP
NewPort平移台ESP301的控制程序，根据说明书自己编写的，不当之处请指正，串口通信，附有说明书。(Cord for Newport ESP301.)
- 2021-01-02 17:18:56下载
- 积分：1
-
EMD
采用Labview编写的EMD算法实现过程，没有借助Matlab，完全通过Labiview控件自主完成(EMD algorithm written using Labview implementation process, there is no means of Matlab, entirely independently completed by Labiview controls)
- 2020-12-29 20:49:00下载
- 积分：1
-
虚拟示波器
说明： 简单虚拟示波器，能调节幅值，频率，相位和偏移量四种变量。(Simple virtual oscilloscope can adjust four variables: amplitude, frequency, phase and offset.)
- 2019-04-08 13:16:59下载
- 积分：1
-
LabVIEW LabSQL工具包
LabVIEW LabSQL工具包，资料完整，vi有额外补充。(LabVIEW LabSQL Toolkit)
- 2018-10-09 09:57:07下载
- 积分：1
-
infinite-power-short-circuit
MATLAB编写无穷大电源发生三相短路的程序，已通过编译，有仿真结果(Infinite power happens three phase short circuit)
- 2013-09-26 10:34:56下载
- 积分：1
-
test-2
LABVIEW程序，实现BP神经网络，能达到目标精度。(This program is write for BP network)
- 2015-03-11 14:25:35下载
- 积分：1
-
yanhuashucaiDAQ
说明： labview数据采集 基于研华数据采集卡的数据采集labview程序设计(LabVIEW data acquisition)
- 2021-01-02 11:09:35下载
- 积分：1
-
hanshuxinhaofashengqi
1．采用Labview设计一虚拟函数信号发生器， 通过数据采集卡输出波形信号，调节信号的相关参数，可观察示波器上波形的变化情况。
⑴ 以NI MyDAQ数据采集卡作为输出接口；
⑵ 数据采集卡输出多种信号，至少完成三种波形：正弦波、三角波、方波(可调占空比)的输出，同时前面板上显示各输出波形；
⑶ 频率、幅值、初相位、直流偏移量和方波的占空比（0～100 ）等参数可以通过前面板控件调节。
⑷ 前面板可显示输出波形。(1. Labview design using a virtual function signal generator, data acquisition card output waveform signal, adjust the relevant parameters of the signal can be observed on an oscilloscope waveform changes.
⑴ with NI MyDAQ data acquisition card as output interface
⑵ data acquisition card output a variety of signals, to complete at least three waveforms: sine wave output, triangle wave, square wave (adjustable duty cycle), while each of the output waveform is displayed on the front panel
⑶ frequency, amplitude, initial phase, the DC offset and duty cycle square wave (0 to 100 ) and other parameters via the front panel controls to adjust.
⑷ output waveform can be displayed on the front panel.)
- 2015-04-25 18:26:52下载
- 积分：1
