-
AR-Mode
LabVIEW AR模型程序及AIC准则(LabVIEW AR model program and AIC criteria)
- 2013-11-27 17:26:36下载
- 积分：1
-
SNAKE
LABVIEW贪吃蛇案例程序，希望能有用！(Snake Case LABVIEW program, hoping to be useful!)
- 2014-01-05 18:59:36下载
- 积分：1
-
直流电机转速控制.tar
说明： 基于转速环-电流环双闭环控制的直流电机调速系统的labview上位机程序。(The LabVIEW upper computer program of DC motor speed control system based on double closed-loop control of speed-loop and current-loop.)
- 2019-06-17 16:55:09下载
- 积分：1
-
LabVIEW LabSQL工具包
LabVIEW LabSQL工具包，资料完整，vi有额外补充。(LabVIEW LabSQL Toolkit)
- 2018-10-09 09:57:07下载
- 积分：1
-
正弦信号收发
说明： 使用usrp n210,利用Labview实现正弦信号收发，一方面可以利用labview实现实际信号在空中收发，另一方面可以检验设备正常运行。(Using USRP N210 and Labview to transmit and receive sinusoidal signals, on the one hand, it can use LabVIEW to transmit and receive actual signals in the air, on the other hand, it can check the normal operation of the equipment.)
- 2019-05-26 23:10:09下载
- 积分：1
-
Active-Noise-Control
用LabVIEW实现主动噪声控制多通道Fx-LMS算法，可以读取任意wav文件进行降噪处理并得到控制效果。(Active Noise Control with LabVIEW multichannel Fx-LMS algorithm, you can read any wav file for noise reduction and get control results.)
- 2020-09-10 16:38:01下载
- 积分：1
-
baobiao
简单地报表生成程序，包含了文字 表格 曲线图，是很好的学习资料(Simple report generation program includes a text table curve, is a very good learning materials)
- 2013-07-17 11:32:58下载
- 积分：1
-
自功率谱VI
自功率谱是分析非平稳信号频谱的重要手段。对于非平稳信号来说，利用自功率谱分析能够更容易找到信号中能量聚集区域，对信号中的频率分布有更好的了解。本文件中将其制作成独立子VI方便程序直接调用。(Self power spectrum is an important method to analyze the spectrum of non-stationary signals. For non-stationary signals, it is easier to find the energy accumulation region in the signal by using self power spectrum analysis, and better understand the frequency distribution in the signal. This document will be made into an independent sub VI convenience program to call directly.)
- 2017-07-29 20:16:16下载
- 积分：1
-
采集系统最终版
labview编写采集数据程序，数据采集后会有相应的频谱分析(LabVIEW writing data acquisition program)
- 2020-11-24 18:19:33下载
- 积分：1
-
Time-domain-analysis-system
本系统可做自动控制原理中的时域分析仿真实验，系统特性如下：
1：可选择仿真系统为一阶、二阶、任意阶
2：可选择信号源为正弦波、三角波、锯齿波、方波（可模拟阶跃信号），并可调节信号源频率、幅值、相位、偏移、方波占空比
3：可选择信号采样率及采样数
4：自动计算传递函数
5：自动计算时域响应参数（增益系数、上升时间、峰值、峰值时间、稳定时间、超调量）
6：波形图同时显示原始信号和响应信号
注：使用本系统需安装labview控制设计与仿真库(The system can do automatic control theory in the time-domain analysis simulation, the system behaves as follows: 1: simulation system can be selected for the first, second, any order 2: select the signal source is a sine wave, triangle wave, sawtooth, square wave (analog step signal), and can adjust the signal source frequency, amplitude, phase, offset, duty cycle square wave 3: the the optional signal sampling rate and the number of samples 4: automatic calculation of the transfer function 5: Automatic calculation domain response parameters (gain coefficient, rise time, peak, peak time, settling time, overshoot) 6: waveform diagram shows both the original signal and the response signal Note: Use the system to be installed LabVIEW Control Design and Simulation library)
- 2013-05-12 11:53:34下载
- 积分：1
