-
c13_tiv1
发生在时变系统中所展示的频谱扩展。待仿真系统是一个简单系统，其中系统的代桶输入是一个形为x(t)=cos[2π(f0+f1)t]的“音频”。(Occurred in the time-varying system in spread spectrum display. Subject to the simulation system is a simple system in which the generation of the system input is a bucket-shaped to x (t) = cos [2π (f0+f1) t] of the " audio." )
- 2013-09-07 09:14:40下载
- 积分：1
-
pi4QPSK
程序实现了基于MATLAB的pi/4 QPSK的仿真,系统在相同条件下，对加噪声和没有噪声的情况，分别画出了它的眼图分析其性能，及已调制信号的时域波形和频谱。(The program realizes the simulation of pi/4 QPSK based on MATLAB. Under the same condition, the system draws its eye diagram to analyze the performance of the noise and no noise, and the time domain waveform and spectrum of the modulated signal .)
- 2021-04-05 22:39:03下载
- 积分：1
-
package_emd
本源程序是用MALAB编写，并且主要是从图像处理方面研究的(The source code is written using MALAB, and mainly from the study of image processing)
- 2011-01-19 11:41:40下载
- 积分：1
-
StackMapFrameVisitor
Stack Map Frame Visitor Source Code for Andriod.
- 2014-01-03 19:38:24下载
- 积分：1
-
matlabshiyucaiyang
MATLAB实现连续信号采样、频谱分析和采样信号恢复的方法。计算在临界采样、过采样、欠采样三种不同条件下恢复信号的误差，并由此总结采样频率对信号恢复产生误差的影响，从而验证时域采样定理。(MATLAB continuous signal sampling, spectral analysis and sampling signal recovery method. Calculated in a critical sampling, the oversampling signal error recovery due to the sampling of the three different conditions, and thereby generate error summarizes the sampling frequency for signal recovery, in order to verify the time domain sampling theorem.)
- 2013-05-17 22:24:41下载
- 积分：1
-
robot-trajectorytrack
机器人轨迹跟踪程序，采用控制器设计方法，可以实现跟踪圆弧、直线、螺旋曲线(Trajectory tracking program, using the controller design method can trace an arc, line, curve spiral)
- 2021-04-15 23:28:54下载
- 积分：1
-
onephaseRMS
采用并网电压有效值控制，作为电流内环的给定参考值，单位功率因素运行(use RMS control the voltage and the current)
- 2016-09-07 16:24:12下载
- 积分：1
-
大气湍流模拟
大气湍流相位屏模拟举例，对研究激光大气传输有一定帮助(an example of phase screen which is helpful to the research of the transmit of laser)
- 2018-08-12 20:09:10下载
- 积分：1
-
EstimateHorizon
matlab中计算并且标出图片中的地平线(matlab to calculate and mark the picture horizon)
- 2013-04-26 19:38:42下载
- 积分：1
-
flightcode
This script will setup the nonlinear simulation (UAV_NL.mdl) and call
trim and linearization routines. Select the desired aircraft here in this
script, via the "UAV_config()" function call.
- 2013-07-20 16:01:11下载
- 积分：1
