-
mimo4
This program implements equation (2.26) using the waterfilling
algorithm
- 2010-08-24 19:24:45下载
- 积分：1
-
test
一个小程序，matlab关于热传导问题的动画程序(A small program, matlab animation on the heat transfer process)
- 2011-04-22 10:28:42下载
- 积分：1
-
hundun
这是关于混沌理论及应用方面的基础资料,希望对大家有帮助,里面含有几个falsh信道模型(This is on the application of chaos theory and the basis of information you would like to help, which contains several falsh channel model)
- 2009-04-23 21:30:13下载
- 积分：1
-
test-lms
自适应信号处理，最终的权值矩阵就是滤波器的系数，学习曲线描述其收敛特性(Adaptive signal processing, the final weight matrix is the filter coefficient, the learning curve to describe the convergence properties)
- 2008-06-04 09:27:07下载
- 积分：1
-
vowelA
Vowel filter for matlab
- 2014-12-24 22:23:20下载
- 积分：1
-
GA
说明： 基因演算法genetic algorthim的程式實現，可利用此程式找出最佳化解(Genetic algorthim genetic algorithm implementation of the program, this program can be used to resolve the best)
- 2009-04-03 18:50:24下载
- 积分：1
-
chap3
典型隶属函数仿真程序 matlab仿真 (Typical membership function simulation program matlab simulation)
- 2010-05-22 11:16:49下载
- 积分：1
-
mod16qam
Multiple input multiple output orthogonal frequency division multiplexing (MIMO-OFDM) is very sensitive to the carrier frequency offset (CFO), which not only affects the channel estimation but also the selection of a minimum error probability based precoder for peak-to-average power ratio (PAPR) reduction such that the system performance will degrade. This paper presents the joint scheme of CFO) and channel estimation in the MIMO-OFDM systems with the minimum error probability based precoder for reducing PAPR. We provide the solution to eliminate the effects of ICI due to CFO mismatch for OFDM with space frequency block codes and spatial multiplexing, drive a generalized linear model and propose a non-iterative reduced complexity model. Our proposed scheme is effective in estimating and compensating for frequency-independent and frequency dependent transmit and receive ICI in the presence of a carrier frequency offset.
- 2014-12-11 23:38:55下载
- 积分：1
-
通过 matlab 编程实现捷联惯导系统初始对准、惯导解算的全过程
通过 matlab 编程实现捷联惯导系统初始对准、惯导解算的全过程。
1）初始自对准：利用前10分钟实验车静止的数据进行惯导系统的自对准。采用前2分钟数据进行解析粗对准，后8分钟数据用五状态Kalman滤波器实现精对准；为了验证精对准性能，可在粗对准结果上把航向角人为加一定幅度（如10度）的误差，观察精对准的收敛性能。
2）纯惯导解算：对准结束后转入纯惯性导航解算，要求进行双子样的圆锥和划摇补偿，即每20ms完成一次导航解算，输出完整的导航结果包括三个姿态、两个水平速度和两个水平位置（天向通道发散不必输出），并给出姿态、速度、位置随时间的变化曲线以及位置误差曲线。(The whole process of initial alignment and inertial navigation solution of strapdown inertial navigation system is realized by matlab programming.)
- 2021-04-21 11:18:49下载
- 积分：1
-
Two_degree_of_freedom_vehicle_model
说明： 如果对实际工程结构作简化处理，建立其动力学模型，并确定系统的质量、刚度、阻尼参数，便可以用多种方法建立系统的动力微分方程。常用的方法有直接 法、影响系数法、拉格朗日法以及有限元法等。拉格朗日法是从能量的观点建立系统的动能T、势能U和功W之间的标量关系，是研究静、动力学问题的一种方法。如果在选定运动坐标以后，能够设法求得坐标相对应的质量矩阵和刚度矩阵，就可以用影响系数法建立多自由度系统运动微分方程[4]。本文采用拉格朗日法建立了1/4车辆几何模型。(If the actual engineering structure is simplified, its dynamic model is established, and the mass, stiffness and damping parameters of the system are determined, the dynamic differential equation of the system can be established by various methods. The commonly used methods are direct method, influence coefficient method, Lagrange method and finite element method. Lagrange method is a method to study the static and dynamic problems, which is to establish the scalar relation among kinetic energy t, potential energy u and work W from the point of view of energy. If the mass matrix and stiffness matrix corresponding to the coordinates can be obtained after the motion coordinates are selected, the differential equation of motion of the multi degree of freedom system can be established by the influence coefficient method [4]. In this paper, 1 / 4 vehicle geometry model is established by Lagrange method.)
- 2019-12-23 16:13:14下载
- 积分：1
