登录
首页 » matlab » 5

5

于 2013-05-02 发布 文件大小:518KB
0 211
下载积分: 1 下载次数: 44

代码说明:

  基于相位调制器产生六倍频光毫米波的 OFDM信号光传输系统研究 (A Radio Over Fiber System with Frequency Sextuple Optical Millimeter Wave Generation Carrying OFDM Signal Utilizing Phase Modulator)

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • SpreadSpectrum
    This simulink program simulates the overall performance of Spread spectrum technique.
    2010-09-29 19:39:22下载
    积分:1
  • Viterbi_Conv_DecodeM
    Viterbi 编解码算法仿真实现,回环调试成功!(Viterbi coder and decoder matlab code)
    2013-12-05 23:32:24下载
    积分:1
  • pskpam
    psk and pam modulation and demodulation with noise
    2013-12-10 23:43:55下载
    积分:1
  • complex_pump_0_02
    介绍如何用较复杂的方法去优化对负载具有感知特性的“黑匣子”模型的神经网络控制。(Shows how to use the complex method to optimize a black-box neural network model of a load-sensing )
    2009-04-02 19:20:49下载
    积分:1
  • Opencv2cV
    OpenCV 2 Computer Vision Application Programming Cookbook
    2014-11-30 10:53:41下载
    积分:1
  • glottal_pulse
    This function generates a pulse train unit amplitude, is then filtered with an exponential model of the glottis.
    2011-09-28 02:53:03下载
    积分:1
  • Robust-Sparse-Coding
    文獻「Robust Sparse Coding for Face Recognition」 及matlab代碼(「Robust Sparse Coding for Face Recognition」 and matlab source code.)
    2012-09-12 20:38:44下载
    积分:1
  • SC-FDE
    单载波频域均衡系统matlab仿真程序。信道使用的是多径瑞利衰落信道。(The single-carrier frequency domain equalization system Matlab simulation program. Channel using multipath Rayleigh fading channels.)
    2021-02-27 16:19:36下载
    积分:1
  • 3
    说明:  IMPARARE IL C++ in 2 ore e mezzo? Modulo-3
    2015-03-10 23:13:52下载
    积分:1
  • three_dim_plot
    The model used for creating the reference voltage is shown in Fig. 4. First, photovoltaic output current (Ipv) and output voltage (Vpv) are passed through a first order low pass filter with a magnitude of G = 1 and a time constant of T = 0.01 seconds in order to filter out the high frequency components or harmonics from these signals as shown in Fig. 5 and Fig. 6. The filtered current and voltage signals (Ipv_F and Vpv_F) are then fed into the MPPT control block that uses the Incremental Conductance Tracking Algorithm. An algorithm that is based on the fact the slope of the PV array power curve shown in Fig. 7 is zero at the Maximum Power Point (MPP), positive on the left of the MPP, and negative on the right. The MPP can thus be tracked by comparing the instantaneous conductance (I/V) to the incremental conductance (∆ I/∆ V) [11] as in (1):
    2013-07-23 17:56:06下载
    积分:1
  • 696516资源总数
  • 106913会员总数
  • 8今日下载