-
风力摆003.1
2015年全国大学生电子设计大赛-风力摆控制系统,(Wind Pendulum Control System in the National College Students Electronic Design Competition in 2015)
- 2020-06-21 10:40:02下载
- 积分:1
-
dianzhen
一个单片机开发实例,可以用开发板实现点阵的规律闪烁发光(A microcontroller development example, you can use the law of the development board to achieve lattice twinkling)
- 2010-11-02 12:41:38下载
- 积分:1
-
modbus-c51-slave
这是在STC2052单片机上实现的C51程序,内容是用于实现MODBUS总线RTU方式的从机源代码。系统基于RS485总线。(This was achieved on C51 MCU STC2052 program content is used to implement MODBUS bus RTU slave mode of the source code. System is based on RS485 bus.)
- 2009-11-02 17:48:51下载
- 积分:1
-
JTD
利用单片机的定时器定时,令十字路口的红绿灯交替点亮和熄灭,实现主支路路口的交通信号灯控制(尽可能保持主线的畅通,即在通常情况下,保持主线的放行,只有在支线到达时,才放行支线),同时采用LED数码管或LCD显示倒计时时间。(The use of single-chip timer timing, make the turn at the crossroads of the traffic lights lit and extinguished achieve the main traffic lights at the junction of the slip control (as much as possible to maintain the smooth flow of the main line, that is, in normal circumstances, to maintain the main line of the release, only at Extension arrive only when the release of the Spur Line), while the use of LED digital tube or LCD display countdown time.)
- 2009-03-12 22:23:43下载
- 积分:1
-
shiboqi
说明: 一个labview做的虚拟的示波器程序,功能比较全,还不错~~~(To do a virtual oscilloscope labview program and functions all, not bad ~ ~ ~)
- 2011-03-01 22:39:49下载
- 积分:1
-
cJSON-test
JSON脚本C语言使用的案例,包括C语言对JSON脚本的输入和输出。(JSON scripting language used C cases, including the C language for JSON script input and output.)
- 2015-03-31 09:47:38下载
- 积分:1
-
STM32F107_CAN_LIN
基于STM32的CAN LIN收发通信程序,自测通过(STM32 based CAN LIN transceiver communication program)
- 2020-08-28 09:48:12下载
- 积分:1
-
code
基于51单片机两相四线步进电机驱动程序,本程序可用42,57系列步进电机,工作方式为八拍。(Based on 51 single-chip two phase four line stepping motor driver, this program can use 42, 57 series of stepper motor, working mode is eight.)
- 2018-03-26 15:48:01下载
- 积分:1
-
4
说明: 单片机位移控制流水灯,C放言和汇编语言,proteus仿真(SCM displacement control water lamp, C release and assembly language, proteus simulation)
- 2018-06-05 18:36:24下载
- 积分:1
-
avr_com
//实验板的AVR程序,uart应用,和计算机通讯,回送PC发送的数据
//接线定义:PD0-RXD PD1-TXD 开关位置:SW6-7/8打开。
//使用串口调试器,使用十六进制方式,首先让PC发送一个字符给MCU,然后将接收到MCU返回的值。
//记事:本程序旨在对uart的理解与演示,程序适合初学者使用.
//使用片外8MHz晶体,9600bps波特率(//Experimental board AVR procedures, uart applications, and computer communications, PC loopback send data// connection definition: PD0-RXD PD1-TXD switch location: SW6-7/8 open.// Use the serial port debugger, use the hexadecimal mode, let PC send a character to the MCU, and then will receive the MCU to return value.// Note: This program seeks to UART understanding and demonstration of procedures suitable for beginners to use.// Use the chip 8MHz crystal, 9600bps baud rate)
- 2007-10-26 20:41:31下载
- 积分:1