网站首页

登录

shiyingdu.zip

于 2020-12-04 发布文件大小:7KB

 0  221

下载积分: 1 下载次数: 11

我要下载

代码说明：

该算法是基于遗传算法跟量子遗传算法运算中两者的适应度曲线合并的程序。使用该程序能更好的对比两者的适应度以及收敛速度。(The algorithm is based on genetic algorithm computation with quantum genetic algorithm in both curves merge fitness program. Fitness contrast both to better use the program as well as the convergence rate.)

文件列表：

合并适应度曲线
..............\angle.m,1719,2012-04-15
..............\cross.m,605,2010-10-21
..............\generation.m,306,2012-04-16
..............\intipop.m,214,2012-04-06
..............\maxfit.m,193,2010-10-21
..............\measure.m,399,2010-10-21
..............\objfunc.m,518,2012-04-15
..............\randprob.m,248,2012-04-16
..............\Untitled.m,1680,2014-07-13
..............\交叉策略.xls,10752,2012-04-06
..............\各子函数.txt,284,2012-04-06

下载说明：请别用迅雷下载，失败请重下，重下不扣分！

发表评论

0 个回复

power-factor-improvement
power factor improvement program

2011-02-14 23:45:23下载

积分：1
LS
说明：本程序给出了最小二乘滤波算法的具体编程，程序中分析比较了自相关算法、协方差算法、前后向加窗算法的滤波效果(This procedure gives the least squares filtering algorithm specific programming, program analysis and comparison of the auto-correlation algorithm, covariance method, before and after windowing algorithm to the filtering effect)

2010-04-12 10:44:50下载

积分：1
Wiener-filter
matlab的维纳滤波器源码，内容较少，但滤波器的功能都有！(the source code of Wiener filter)

2011-06-11 10:39:00下载

积分：1
Taxicab_CCDF
THIS IS THE MATLAB SOURCE CODE

2014-02-25 11:50:04下载

积分：1
SpatialMultiplexing_ClosedLoop_Mode4
LTE下行链路空分复用闭环。仿真配置：16QAM调制、1/3码率Turbo编码、10MHz带宽、每个子帧一个PDCCH符号、单码字，8次迭代Turbo译码、早期终止机制、MMSE（最小均方误差）MIMO接收器，PDSCH发射端进行空分复用预编码。信道模型是LTE-MIMO信道附加AWGN信道。(LTE downlink closed loop space division multiplexing. Simulation Configuration: 16QAM modulation, 1/3 rate Turbo code, 10MHz of bandwidth, one PDCCH per subframe symbol, single code word, 8 Turbo decoding iterations, early termination mechanisms, the MMSE (minimum mean square error) the MIMO receivers, PDSCH transmitting terminal space division multiplexing precoding. Channel model is LTE-MIMO channel additional AWGN.)

2016-12-10 00:48:03下载

积分：1
key-frame-extraction
in this zip folder contains the how to extract the key frames and how to add the noise and RGB.

2013-10-01 23:44:05下载

积分：1
battery-canshu
介绍了采用电化学阻抗谱来进行锂电池的模型参数分析(lithium battery parameter estimation)

2014-02-10 14:25:10下载

积分：1
mifaandfanmifa
计算特征值和特征向量的幂法和反幂法以及计算矩阵的minres 算法的matlab程序(calculated eigenvalues and eigenvectors of power and anti-power-law and calculate the matrix algorithm mat minres lab procedures)

2007-01-01 16:39:26下载

积分：1
chapter4
几个matlab例子。对于初学者有很好的帮助，可以试试看。。挺不错的(Several matlab example. Good help for beginners, you can give it a try. . Very good)

2012-05-24 12:41:49下载

积分：1
matlab
1. 给一段原始的语音信号（可以是自己录制的一段语音），加上一频率为3.8kHz的高频余弦噪声和频率为3.6kHz的高频正弦噪声（幅度自己可以选择），用窗函数设计一滤波器（要求最小阻带衰减为50dB）对加噪后的语音信号进行滤波，画出滤波器的频率响应曲线，画出滤波前后的时域图和频谱图。需要用到的函数： fir1 用窗函数设计FIR滤波器的函数 2. 用GUI设计一界面（如图1所示）完成如下功能： 1）输入一语音信号，画出语音信号的时域图和频谱图； 2）对语音信号加噪处理，画出加噪后的时域图和频谱图； 3）给定滤波器的性能指标，采用几种不同的方法设计滤波器对加噪信后进行滤波，画出各滤波器的频率响应曲线，画出滤波后的时域图和频谱图。 (1. to some of the original speech signal (which can be a voice you record yourself), plus a cosine frequency of 3.8kHz frequency noise and frequency of 3.6kHz frequency sinusoidal noise (in the range that they can choose), with a window function to design a filter (requires a minimum stop band attenuation is 50dB) after adding noise to the speech signal is filtered, the filter frequency response curve to draw, draw diagrams and time-domain spectrum before and after filtering. Need to use the function: function fir1 with window function design FIR filter design 2. Using a GUI interface (Figure 1) complete the following functions: 1) an input speech signal, the speech signal in the time domain to draw graphs and spectrum 2) adding noise to the speech signal processing, draw diagrams and time-domain plus noise spectrum after 3) to set the filter performance, using several different methods designed to filter letter after adding noise filtering, draw the frequency response curve of each )

2015-01-09 10:00:04下载

积分：1

696516资源总数
106913会员总数
8今日下载