-
SPI-429-249
用于步进电机细分驱动，MSP430F149配置TMC429，进而驱动TMC249，细分驱动(Subdivision driver for stepper motor, MSP430F149 configuration TMC429 turn drives TMC249 Subdivision Driver)
- 2013-04-02 21:32:20下载
- 积分：1
-
RaidTest
RAID卡的测试程序，写的不好哈，请大家原谅，(RAID card test procedures and writing bad Kazakhstan,)
- 2009-02-17 11:55:56下载
- 积分：1
-
debye5(1)
说明： 由晶格振动声子态密度计算迪拜温度、比热、振动熵等热力学性质的程序。(the programme for caculation of the debye temprature，specific heat,
entropy and so on from the DOS of phonon )
- 2011-04-18 15:09:14下载
- 积分：1
-
2610IO
dmc2610运动控制卡编写IO输出，对想编写运动控制的人有非常大的帮组(the dmc2610 motion control card write IO output, very large help group for people who want to write the motion control)
- 2020-09-10 05:08:03下载
- 积分：1
-
MFCStatus
parker acr9000运动控制器上位机程序开发例子，主要包括控制器连接和断开以及读取变量(Parker acr9000 motion controller PC program development example, mainly including controller connect and disconnect and read the variable)
- 2020-09-10 05:08:03下载
- 积分：1
-
Wireless-remote-control-program
飞思卡尔16位单片机无线遥控程序，供初学者开发学习(Wireless remote control program)
- 2015-08-15 17:21:31下载
- 积分：1
-
an_r01an0455ej0100_rl78_pwm
瑞萨 pwm 控制（自带头文件）压缩包打包
(Renesas pwm control (from the lead file) compressed packed)
- 2013-08-31 09:00:39下载
- 积分：1
-
AD9910
这是AD9910 DDS芯片的verilog配置程序，经调试已成功，可以供大家参考。(AD9910 verilog configuation.)
- 2010-05-27 10:31:15下载
- 积分：1
-
audio-capture-raw-_console
利用kinect获取原始的音频波形，得到四声道的pcm波形。(Use kinect to get the original audio waveform, get pcm waveform four channels.)
- 2021-01-29 14:18:35下载
- 积分：1
-
C8051F060-AD-UART1
C8051F060 自带高速AD进行数据采集 可达100兆采样率 并切缓存与片外ram 并把采集数据通过串口发送给PC ( Data Acquisition example for C8051F060
Description: This example illustrates the use of ADC1 and the DMA to acquire and store
data. It is intended for use with the C8051F060 target board in the development kit.
// This code measures a signal at the AIN0 input with the 16-bit SAR ADC0.
// The data is sampled at a rate of 100kHz. ADC output data is transferred to
XDATA memory space using the DMA.
//
// With the EMIF configured for off-chip XRAM access (on the upper ports),
this code moves the ADC data to the C8051F060TB target boards s SRAM device.
// Once data acquisition is complete, the code then prompts the user to press the P3.7
// button on the target board when ready to receive the data via the UART0 serial port.
The TB features an RS-232 transceiver and connector, so the data can be transferred
// to a PC via its serial port.
//
The code is set to acquire up to 32768 samples (for 64kbytes of data). The SRAM device -
can accommodate up to 128kbytes, )
- 2014-07-03 18:46:42下载
- 积分：1
