登录
首页 » C++ Builder » stm32_game_pad

stm32_game_pad

于 2013-05-11 发布 文件大小:12087KB
0 162
下载积分: 1 下载次数: 393

代码说明:

  非常好的stm32例子,stm32做游戏手柄,实现方向和8个按键功能(It is a very good for gamepay of stm32)

文件列表:

stm32_手柄(增强版)VET6,兼容win7
...............................\boot
...............................\....\readme.txt,12,2012-08-17

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • ARM7
    NXP系列的ARM7(LPC3132)芯片的裸机驱动,包括gpio,定时器,串口,ad转换等(NXP series ARM7 (LPC3132) bare chip drivers, including gpio, timers, serial, ad conversion, etc.)
    2013-11-16 21:07:53下载
    积分:1
  • Stm32Dma
    用于在stm32103芯片开发中的DMA模块的模板,可以根据自己的需求进行相应的修改(DMA module for STM32103 chip development)
    2018-12-24 16:26:43下载
    积分:1
  • F4DISCO CDC USB example
    说明:  STM32F4 Discovery CDC USB example
    2020-07-15 18:51:53下载
    积分:1
  • 程序及原
    系统中采用了电压反馈闭环,单片机通过内部软件产生一路SPWM控制信号,然后经过逻辑门变换电路变换成逆变全桥所需的四路驱动信号,再经专用驱动芯片TLP250隔离放大后,分别加到逆变全桥四个IGBT的栅极,进行驱动控制。(The voltage feedback closed loop is used in the system, and the single chip microcomputer generates all the SPWM control signal through the internal software, then transforms the four-way drive signal required by the logic gate transformation circuit into the inverter full bridge, and then adds to the gate of four IGBT of the inverter full bridge after the special drive chip TLP250 isolation and amplification, and carries on the drive control.)
    2019-04-24 18:33:46下载
    积分:1
  • ADC_TIM1
    STM32F10X ADC定时器出发方式,STM32例程包之一(STM32F10X ADC start the timer mode, STM32 routine one package)
    2010-09-24 13:18:21下载
    积分:1
  • DAC
    nxp-lpc1768 zlg dac转换程序,实例程序。(nxp-lpc1768 zlg dac)
    2012-05-03 19:15:42下载
    积分:1
  • OBD_CAN读取代码
    简单实现OBD读取功能,stm32f103的主控芯片(Simple implementation of OBD read function)
    2021-03-27 11:39:12下载
    积分:1
  • rtc
    stm32f103 rtc每秒中断串口输出(stm32f103 rtc .every second printf out.)
    2018-11-20 08:14:08下载
    积分:1
  • 电机控制(((上野佐千夫,中文)-2
    说明:  电机控制,上野(日本人)的培训ppt,下册。内容太详细,值得一读。(SVPWM,PMSM,motor control about pmsm.)
    2019-05-28 09:28:43下载
    积分:1
  • BHS STM32 实验29-CAN通讯 (直接操作寄存)
    准备两个CAN板子,连接两个CAN接口,两个板子都下载本程序。 本实验通过CAN总线控制另外一个板子的LED2~LED5闪烁的例子,如果通信正常可以看到两个板子的LED都再闪烁, 如果通信失败或者断开通信线,LED不再闪烁(Prepare two CAN board, connecting the two CAN interface, two board are download the program. This experiment through the CAN bus control another board LED2 ~ LED5 flashing example, if communication normal CAN see two board LED twinkle again, If communication failure or off the line, LED will no longer flash)
    2012-04-16 14:13:56下载
    积分:1
  • 696518资源总数
  • 105885会员总数
  • 31今日下载