-
refbook
Matlab function reference Book Matlab function reference BookMatlab function reference BookMatlab function reference BookMatlab function reference BookMatlab function reference Book
- 2009-10-25 03:03:05下载
- 积分：1
-
arduimu_vD-(1)
arduimu_vD (1).rar arduimu
- 2015-01-13 19:42:07下载
- 积分：1
-
SVPWM125444
a good simulink model of Space Vector PWM
- 2017-04-11 02:36:29下载
- 积分：1
-
MatlabDataType
matlab的数据类型介绍，方便今后使用查看，(Data type in matlab)
- 2015-03-30 18:09:19下载
- 积分：1
-
yale-2.0-src.tar
著名的开源仿真软件yale，功能与matlab完全有得比(Well-known open source simulation software yale, function and matlab completely than has)
- 2007-08-05 02:27:24下载
- 积分：1
-
Convolutional_code_Viterbi_Decoder
卷积码的维特比译码程序，运用MATLAB语言(Viterbi convolutional code decoding program, the use of MATLAB language)
- 2011-01-05 21:30:53下载
- 积分：1
-
GPC
提供了对象已知与未知的广义预测控制（GPC）算法，包含有单步与多部的Diophanine方程求解。(Provides object known and unknown generalized predictive control (GPC) algorithm, includeing single-step and multi-unit Diophanine equation.)
- 2013-08-27 19:14:36下载
- 积分：1
-
Centroid
WSN 质心定位算法 Centorid Algorithm
加经典参考文献
A: 如果接受节点接收到的包数目与发送节点发送的包数目的比值大于CM_threshold,则这两个节点视为邻居节点
未知节点利用邻居锚节点进行定位，没有邻居锚节点的未知节点无法定位。
B:
如果接受节点接收到的包数目与发送节点发送的包数目的比值大于CM_threshold,则这两个节点视为邻居节点
未知节点一旦被定位就充当起锚节点的功能，向周围邻居发送自己的估计坐标信息
未知节点把已经定位的未知节点与锚节点同等对待
C:
如果接受节点接收到的包数目与发送节点发送的包数目的比值大于CM_threshold,则这两个节点视为邻居节点
有邻居锚节点的未知节点只利用邻居锚节点进行定位，没有邻居锚节点的未知节点才利用已经定位了的邻居未知节点进行定位。(WSN centroid localization algorithm Centorid Algorithm
A: If you accept the received packet node number and the number of packets sent by the sending node ratio greater than CM_threshold, then these two nodes as neighbors
Unknown node using the neighbor anchor nodes to locate, no neighbors anchor nodes and unknown nodes can not be located.
B:
If you accept the received packet node number and the number of packets sent by the sending node ratio greater than CM_threshold, then these two nodes as neighbors
Unknown nodes are positioned on as soon as the function of anchor nodes to send their neighbors estimated coordinate information
Unknown unknown node to node already positioned anchor nodes treated equally
C:
If you accept the received packet node number and the number of packets sent by the sending node ratio greater than CM_threshold, then these two nodes as neighbors
Of the unknown neighbor anchor node the neighbor nodes are only positioned anchor nodes, )
- 2013-08-31 19:13:47下载
- 积分：1
-
VESPRITlike
可以直接计算信号的四阶累计量，挺不错的小程序，注意信号必须是非高斯信号哟。(Signals can be directly calculated fourth-order cumulant, very good small procedures, the attention signal must be a non-Gaussian signal yo.)
- 2007-11-27 11:46:28下载
- 积分：1
-
tools
非线性振动必备工具箱，里面有详细的步奏讲解,频谱分析，poincare截面，分岔图，李雅普洛夫图(onlinear vibration necessary toolbox, There are detailed explanations of the steps for spectrum analysis, poincare section, bifurcation diagram and lyapunov figure
)
- 2012-03-27 20:37:47下载
- 积分：1
