登录
首页 » Visual C++ » 31---Recursion

31---Recursion

于 2015-04-04 发布 文件大小:586KB
0 187
下载积分: 1 下载次数: 5

代码说明:

  this is simple recursion code for beginners...

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • momitor
    监视程序,能监视系统有没有打开扫雷程序,如果打开就关闭,其窗口自动隐藏,按ALT+F10调出窗口,(Monitoring program, can monitor the system has no open mine program, if the opening is closed, its windows auto-hide, press ALT+ F10 transferred out of the window,)
    2009-10-03 03:34:46下载
    积分:1
  • ranyouxiaohao
    燃油消耗率一直是大家关注的问题,本程序采用matlab编程,绘制不同转速下发动机的燃油消耗率(The fuel consumption has been an issue of concern, the procedures used Matlab programming, drawing different speeds the engine s fuel consumption rate)
    2013-05-07 13:29:55下载
    积分:1
  • SimpleService
    How to start or stop a windows NT service.
    2006-09-27 19:32:17下载
    积分:1
  • Bartlettmethod
    bartle自功率谱密度分析,对于直接法的功率谱估计,当数据长度N太大时,谱曲线起伏加剧,若N太小,谱的分辨率又不好,因此需要改进。(Bartle since the power spectral density analysis, for the direct method of power spectrum estimation, when the data length N is too large, the spectrum curve of the ups and downs, if N is too small, the resolution of the spectrum and is not good, so need to improve.)
    2014-09-26 15:29:33下载
    积分:1
  • SURFmex
    matalab调用C程序实现的基于SURF算法的全景图像拼接(matalab call C SURF algorithm based Program for panoramic image stitching)
    2011-05-03 08:30:54下载
    积分:1
  • MatlabandVC
    该代码提供了MATLAB与VISUAL C++的接口编程,为MATLAB可视化编程提供了方便(The code provides a MATLAB with VISUAL C++ Interface programming, visual programming for MATLAB provides a convenient)
    2007-08-13 11:12:07下载
    积分:1
  • Runge-Kutta-
    应用四阶龙格库塔法求解微分方程的初值问题(Applications fourth-order Runge-Kutta Solving Ordinary Differential Equations)
    2015-01-28 17:43:33下载
    积分:1
  • emailparser
    解析email的源代码。 mine协议 解码译码(analytic email source. Mine agreement decoder decoding)
    2006-10-22 14:00:09下载
    积分:1
  • job
    有m台不同的机器,n个不同的工件。每个工件有多道工序,每道工序由指定的机器在固定的时间内完成。一道工序一旦开始处理,就不能中断。每台机器一次只能处理一道工序。一个调度就是决定每台机器上工序的处理顺序,使得机器完成所有工件的时间最短。具体的,该问题就是要求在满足(1)、(2)两个约束条件的前提下,确定每台机器上工序的顺序,使加工的时间跨度(从开始加工到全部工件都加工完所需要的时间)达到最小。其中,(1)表示工件约束条件:对每个工件而言,机器对它的加工路线是事先确定的;(2)表示机器约束条件:对每台机器而言,一次只能对一道工序进行加工。()
    2007-09-18 23:30:48下载
    积分:1
  • 104
    数字移动:图中的九个点上,空出中间的点,其余的点上任意填入数字1到8.1的位置固定不动,然后移动其余的数字,使1到8顺时针从小到大排列.移动的规律是:只能将数字沿线移向空白的点. (Digital Mobile: Figure in the nine points, empty out the middle point, the rest of the points fill any position of the numbers 1 to 8.1 fixed and then move the rest of the figures, and make 1-8 clockwise from small to large array . The law of movement is: can only move along the number of blank spots.)
    2009-11-15 21:33:11下载
    积分:1
  • 696518资源总数
  • 106010会员总数
  • 4今日下载