登录
首页 » PDF » STATCOM.nh

STATCOM.nh

于 2013-12-16 发布 文件大小:2818KB
0 81
下载积分: 1 下载次数: 7

代码说明:

  一遍关于单周控制三相四线制静止无功发生器研究的文章(the reserach of three-phase four-wire static Var Generator with One-cycle Control)

文件列表:

STATCOM.nh.nh,3124150,2010-07-09

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • PWM输出
    说明:  使用STM32F103 32位芯片配置定时器以及控制定时器输出PWM波形(Using STM32F103 32 bit chip to configure timer and control the output PWM waveform of timer)
    2020-06-23 16:00:01下载
    积分:1
  • ADX345
    基于STM32的adx345加速度传感器代码。( U57FA u4E89M0 u7684g4A0 u901F u5EA6 u4F20 u611F u5668 u4EE3 u7801 u3002)
    2017-05-21 11:18:50下载
    积分:1
  • FastICA_negentropy
    基于负熵的盲源分离,使用FastICA技术,适合初学者(BSS based on negentropy by FastICA)
    2014-01-03 14:38:31下载
    积分:1
  • CCPUTemp
    通过EC获取CPU的运行温度,对CPU的运行温度进行实时监控,超过会自动报错,并可以设置监控时间(read CPU s temperture by EC)
    2020-07-20 21:38:45下载
    积分:1
  • led屏
    p10 LED 显示屏驱动程序,很适合新手学习的方法(P10 LED display driver, it is suitable for beginners to learn the method)
    2017-07-20 10:51:42下载
    积分:1
  • 18b20
    使用51单片机和18B20采集温度,并用数码管显示(Use 51 And 18B20 collecting temperature and with digital display)
    2013-09-20 09:16:20下载
    积分:1
  • STM8_DevelopmentEnvironmentSmallestProjectSystem
    说明:  STM8 开发环境、最小项目工程、最小系统 二、STM8S的最小硬件系统 STM8的最小硬件系统包含下列部分: 1、电源 2、时钟管理 3、复位管理 4、调试接口(SWIM) (Development EnvironmentSmallestProjectSystem)
    2010-04-17 15:09:50下载
    积分:1
  • STM32W8686-SDIO-ADHOC-STA
    用STM32驱动WIFI模块MARVELL8686的驱动程序,分别包含了ADHOC和STA模式,同时附带了上位机执行程序,可无线采集摄像头的图像(WIFI module by driving MARVELL8686 STM32 driver, respectively, and contain ADHOC STA mode, and the PC program execution comes, the image acquisition camera wirelessly)
    2021-01-18 17:58:44下载
    积分:1
  • ex5-1
    这是一个使用8051制作的数字时钟,使用2个弹跳按钳和4个共阳七段显示器组合而成.(It is a production of the 8051 Digital Clock, use two bouncing by clamp and four monitors in paragraph 107 of a total of Shenyang combination.)
    2007-01-16 00:10:13下载
    积分:1
  • a
    说明:  设计一个VI来测量温度(保留2位小数),每隔0.25秒测一次,共测定10秒。在数据采集过程中,VI将在波形Chart上实时地显示测量结果。采集过程结束后,在Graph上画出温度数据曲线,并且把测量的温度值以文件的形式存盘, 使用记事本打开文件检查结果是否正确。 存盘格式为: 点数 时间(S) 温度值(度) 1 0.25 78.56 2 0.50 85.32(Design a VI to measure the temperature (keep two decimal places), measured once every 0.25 seconds, 10 seconds were measured. In the data collection process, VI will display the measurement results in real time on the waveform Chart. After the acquisition process, the temperature data in the Graph draw curves, and the temperature measured in the form of document archiving, Use Notepad to open the file to check the result is correct. Save format: Points Time (S) temperature (degrees) &nbsp 1 0.25 78.56 &nbsp 2 0.50 85.32)
    2014-04-16 12:24:25下载
    积分:1
  • 696522资源总数
  • 104027会员总数
  • 45今日下载