-
FFT
使用labview实现了FFT的变换，此方法更为简单快捷，同时简单明了(Labview achieved using FFT transform, this method is more simple and quick, and simple)
- 2021-04-17 14:58:53下载
- 积分：1
-
fashengqi
基于labview的虚拟波形发生器，能够实现正弦、余弦、锯齿波的产生(Labview-based virtual waveform generator, to achieve the sine, cosine, sawtooth generation)
- 2013-12-22 16:15:06下载
- 积分：1
-
velocity-control-for-yaskawa-motor
可以实现安川交流电机的调速，检查伺服准备就绪，伺服ON,及调速。(Can achieve Yaskawa AC motor speed, check the servo ready, servo ON, and speed.)
- 2013-09-12 17:04:05下载
- 积分：1
-
1
说明： LABVIEW的BP神经网络曲线拟合程序(the BP ANN exe based on LABVIEW )
- 2015-11-21 11:21:49下载
- 积分：1
-
二进制文件读取
利用Labview软件编写读取二进制文件程序(The Labview program reads the binary file)
- 2018-05-22 20:03:20下载
- 积分：1
-
33356
运用labview开发环境，实现串口通讯，接受串口发送接收的数据(Development environment using labview, serial communications, sending and receiving serial data received
)
- 2012-01-09 10:30:09下载
- 积分：1
-
labview_tcp_host_machine
基于TCP协议的Labview网络摄像头视频接收及显示、温湿度监测及控制指令远程发送上位机.vi，机器人下位机装载温湿度传检测、人体感应、红外、烟雾监测等传感器以及网络摄像头，下位机实时采集的图像视频、传感器数据等经过WiFi无线传输，上位机通过TCP协议实时接收下位机传输的数据，显示温湿度、人、烟雾等状态信息，还可以通过Labview上位机向机器人下位机远程发送转弯、前进、上楼梯等运动控制指令，并进行了简单的控件、界面美化(ON划词翻译ON实时翻译
Labview network video camera TCP protocol to receive and display, temperature and humidity monitoring and control of remote host computer sends instruction based on.Vi, robot crew loading temperature and humidity detection, the human body induction, infrared, smoke monitoring sensor and network camera, video image, the lower position machine real-time acquisition of sensor data through WiFi wireless transmission, host computer through the TCP protocol to receive real-time lower computer transmission of data, display of temperature and humidity, people, smoke and other state information, but also through the Labview host computer to the robot slave machine remote transmitting turning, forward, up the stairs and other motion control instruction, and has carried on the simple controls, to beautify the interface)
- 2014-12-11 19:48:13下载
- 积分：1
-
WaveGenerator
Wave Generator for LabWindows, a C based software used to create VIs for LabView
- 2009-11-11 02:09:30下载
- 积分：1
-
用于控制keithley2600数字源表测量太阳电池的IV曲线 IV-curve-measure-with-Keithley2600
该程序可用于控制keithley2600数字源表测量太阳电池的IV曲线。可设置正反扫描次数，实时显示测量结果，并计算Jsc，Voc，FF，eff等电池参数。程序IVnew是总程序，除子程序外，还包括NI公司网站上提供的keithley2600程序包（必要）。(The program can be used to control keithley2600 digital source meter to measure the solar cell IV curve. Can be set to the number of positive and negative scanning, real-time display of measurement results, and calculate the cell parameters of Jsc, Voc, FF, eff. The program ‘IVnew’is the final program.)
- 2020-06-28 10:20:01下载
- 积分：1
-
gongzhenjiantiao
用于对于轴承振动信号的共振解调程序，便于对轴承故障信号进行分析(Used for resonant demodulation of bearing vibration signals for easy analysis of bearing fault signals)
- 2017-03-21 20:13:39下载
- 积分：1
