-
FIR_window
窗函数法设计有限冲激响应（FIR）滤波器，可根据工程上的设计指标来设计。(Window function design finite impulse response (FIR) filters, according to engineering design specifications to design.)
- 2009-01-10 11:10:44下载
- 积分：1
-
ADS-B
一种基于ADS-B、WAM和雷达的组合监视方法及其架构(Based on ADS-B, WAM and a combination of radar monitoring method and its architecture)
- 2013-10-19 11:31:53下载
- 积分：1
-
fenglifadian
风力发电控制器matlab仿真代码，大家一起参考学习。(Wind power controller matlab simulation code, with everyone learning.)
- 2013-11-29 22:16:19下载
- 积分：1
-
RLS_suanfa
说明： 学习自适应天线，RLS最常见一种算法，这里提供其编程思路，供参考(Learning adaptive antenna, RLS algorithm is the most common kind, which offers its programming ideas, for reference)
- 2011-02-23 23:26:49下载
- 积分：1
-
Pso-
关于对pSOriasis的一般性的描述，虽然不是很全，但是还是十分的实用，对于初学者是很有帮助的 (About the general description of pSOriasis, though not very full, but still very useful for beginners is very helpful
)
- 2012-04-11 14:12:52下载
- 积分：1
-
V2_Three_phase_DQ_control
pwm没有做SVPWM，而仅仅是单极性PWM。PI参数调试的不是很好，可能调制波波形不太好(pwm did not do SVPWM, while the Unipolar the PWM. PI parameters debug not very good, may be modulated waveform is not very good)
- 2013-03-14 17:22:21下载
- 积分：1
-
BPnetworktraining
创建和训练BP神经网络的MATLAB程序设计(Creation and training of BP neural network MATLAB Programming)
- 2009-05-17 09:21:55下载
- 积分：1
-
pujianfa
谱减法是利用噪声的统计平稳性以及加性噪声与语音不相关的特点而提出来的。即让有语音期间噪声幅度谱的期望值与无语音间隙噪声的幅度谱的期望值相等。(Spectral subtraction method is the use of stationary noise statistics and the additive noise and speech characteristics not related to the initiative. During that speech so that the expected value of noise amplitude spectrum and noise-free audio gap equal to the expected amplitude spectrum.)
- 2010-12-18 19:10:02下载
- 积分：1
-
signperm
Determinant of the permutation matrix with rows ordered by p.
- 2010-03-06 17:29:40下载
- 积分：1
-
RSF_v0
This code demomstrates an improved algorithm based on the local binary fitting (LBF) model
in Chunming Li et al s paper:
"Minimization of Region-Scalable Fitting Energy for Image Segmentation",
IEEE Trans. Image Processing, vol. 17 (10), pp.1940-1949, 2008.
Usage: These codes can be used for Matlab 7.0.4 or higher versions in Windows.
Run the Demos in the M-files for several test images. Once an image comes out, click
the mouse to generate a polygon as the initial contour: left click to get
a number of points, then right click to get the end point.
The number of iterations may need to be increased if the initial contour is too far
away from the desired object boundary.
- 2011-05-05 01:54:08下载
- 积分：1
|
联系客服（QQ：3324461878）
