-
positioning
调试成功的测距定位仿真（TOA）。三个函数的作用分别是：在一个正方形区域内随机选择10个点；在这10个点中选择被测结点和参考结点；LSE位置计算。(Ranging and Location debug successful simulation (TOA). The role of the three functions are: a square area in 10 randomly selected points 10 points in the selected node under test and reference nodes LSE position calculation.)
- 2010-07-10 11:13:41下载
- 积分：1
-
downlink
matlab with simulink can do simulation of wimax before you can model your system then simulate to improve the performance
- 2010-01-31 06:53:56下载
- 积分：1
-
KF_SINS_modify2
这是一个用MATLAB编写的接联惯性导航系统精对准阶段KALMAN滤波仿真程序的修正程序。解决了因系数矩阵条件数过大造成的滤波发散问题。(using MATLAB access Inertial Navigation System precision alignment stage Kalman filtering imitation really procedures amendment procedure. Solutions for the coefficient matrix several conditions caused by the excessive filtering divergence.)
- 2007-01-28 12:51:22下载
- 积分：1
-
gsc
广义旁瓣抵消器（GSC）是麦克风阵列语音增强中被广泛采用的一种自适应波束形成算法(generalized sidelobe canceller (GSC) is the microphone array speech enhancement which has been widely used in an adaptive beamforming Algorithm)
- 2007-05-08 11:08:06下载
- 积分：1
-
cbl
利用fft()进行快速傅立叶变换，得到频谱，画出正弦函数及其频谱
找出频谱中使得Y轴取最大值时的估计频率记为ft
加入白噪声，绘出信噪比和均方误差的关系曲线
( using fft () for fast Fourier transformation, spectrum, to draw the sine function and its spectrum find the spectrum makes the Y-axis maximum value when the estimated frequency is denoted by ft adding white noise, SNR plot and mean square error curve)
- 2011-01-08 10:52:46下载
- 积分：1
-
FDTD
用matlab实现的时域有限差分法程序，模拟了金属槽的电势分布。(Matlab implementation of the finite difference time domain method program to simulate the potential distribution of the metal tank.)
- 2012-05-14 20:53:02下载
- 积分：1
-
SARBM3D_win32
Matlab和C的混编，用于SAR图像去相干斑，将处理加性噪声的BM3D推广到SAR。(Functions for Matlab for the denoising of a SAR image corrupted
by multiplicative speckle noise with the technique described in
"A Nonlocal SAR Image Denoising Algorithm Based on LLMMSE Wavelet Shrinkage",
written by S. Parrilli, M. Poderico, C.V. Angelino and L. Verdoliva)
- 2013-11-12 22:09:46下载
- 积分：1
-
MATLAB
matlab程序编译成独立exe文件 应用(matlab program compiled into an independent exe file)
- 2010-06-03 17:20:03下载
- 积分：1
-
Implementation-of-HP-IIR-filter-for-a-given-seque
IMPLEMENTATION OF A HIGH PASS INFINITE IMPULSE RESPONSE FILTER FOR A GIVEN SEQUENCE
- 2015-08-14 00:43:12下载
- 积分：1
-
项目4
说明： 任务：设计一个4×2.5Gbit/s 长距离光纤传输系统，并利用OptiSystem 仿真验证。
要求：
1．采用波分复用技术，波长设置以100GHz 为间隔，频率分别为193.1THz、193.2THz、193.3THz、193.4THz，每个波长传输速率为2.5Gbit/s（NRZ），传输距离为300km。采用常规光纤，光纤损耗系数为0.25dB/km。
2．单通道光发送机最大输出功率为0dBm，光接收机的接收光功率不低于－26dBm，过载点为－10dBm。
3．可以采用EDFA 作为线路放大器，其中EDFA 的输入功率限制在－18～2dBm，最大输出功率20dBm，增益范围为13～25dB，噪声指数4.0dB。(Task: Design a 4 x 2.5 Gbit/s long-distance optical fiber transmission system, and use OptiSystem simulation to verify.
Requirement:
1. Using wavelength division multiplexing technology, the wavelength is set at 100GHz intervals, with frequencies of 193.1 THz, 193.2 THz, 193.3 THz and 193.4 THz, respectively. The transmission rate of each wavelength is 2.5 Gbit/s (NRZ), and the transmission distance is 300 km. The loss coefficient of conventional optical fibers is 0.25dB/km.
2. The maximum output power of a single-channel optical transmitter is 0 dBm, and the receiving power of an optical receiver is not less than -26 dBm, and the overload point is -10 dBm.
3. EDFA can be used as line amplifier, where the input power of EDFA is limited to - 18-2dBm, the maximum output power is 20dBm, the gain range is 13-25dB, and the noise index is 4.0dB.)
- 2019-05-13 09:39:41下载
- 积分：1
