-
MAjuguji
MA（q)模型的矩估计方法MATLAB例程(MA (q) model of the moment estimation method of MATLAB routines)
- 2009-07-15 16:48:20下载
- 积分：1
-
baizaos
这是一个用MATLAB编程得到的白噪声程序，主要的作用就是用于学习(White noise generator program, complete procedures for system identification or signal processing)
- 2013-03-28 13:18:01下载
- 积分：1
-
05
说明： 基于kpca以及pca,dpls流形发的程序，应用于故障检测与故障诊断,还有故障识别，识别的效果很好，对象为cstr，程序简单(Based on kpca and pca, DPLS manifold hair of program, used in the fault detection and fault diagnosis, and fault recognition, identification of the good effect, the object for CSTR, procedure is simple)
- 2011-12-26 10:27:59下载
- 积分：1
-
Digital_Signal_Processing_MATLAB_7
MATLAB_7.x数字信号处理配套程序(Digital Signal Processing MATLAB_7.x matching procedures)
- 2009-07-12 16:08:02下载
- 积分：1
-
Imatest-use-guide
Imatest使用指南,可以检测一张图片的参数，比如shading,colorcheck等。(Imatest use guide.it can check a picture paraments for example shading ,colorcheck and so on.)
- 2014-12-05 10:56:04下载
- 积分：1
-
vibration1
说明： 对周期激振力作用下的单自由度无阻尼系统，将激励展开成傅里叶级数，观察其对方波函数的逼近情况，并计算系统的受迫振动。(For the single degree of freedom undamped system under the action of the periodic excitation force, the excitation is expanded into Fourier series, and the approximation of Fang Bo's function is observed and the forced vibration of the system is calculated.)
- 2018-06-09 20:53:38下载
- 积分：1
-
MATLAB
Reading wave file in matlab and putting into packets.
- 2010-11-16 02:19:20下载
- 积分：1
-
few3Dpdf
这是根据提交的亚历山大Gramfort的“MATLAB的网状到PDF与三维交互对象“。他的计划将允许网数字转换成3D PDF格式。然而，他的代码只允许一个层进行转换，并不会启用的透明度。
本意见书不创建最终的PDF。它产生的U3D文件，然后可以使用到PDF的Adobe Acrobat Pro文件插入。本文件还允许多层网格，以创建，并为每个层的透明度指定。
此代码包含一个函数（installGoogleArchive.m），它会自动下载并安装所需的中间数据格式转换（IDTF）进入最后的通用3D（U3D）文件的二进制文件。此代码还只包括转换器的Windows版本。(This submission is based on Alexandre Gramfort s "matlab-mesh-to-pdf-with-3d-interactive-object". His program allows meshes to be converted into 3D PDF figures. However, his code only allows a single layer to be converted, and does not enable transparency.
The present submission does not create the final PDF. It generates the U3D file which can then be inserted into a PDF file using Adobe Acrobat Pro. This submission also allows multilayer meshes to be created, and for the transparency of each layer to be specified.
This code includes a function (installGoogleArchive.m) which will automatically download and install binaries required to convert the intermediate data format (IDTF) file into the final Universal 3D (U3D) file. This code also only includes the windows version of the converter.)
- 2011-05-23 12:34:09下载
- 积分：1
-
ofdm_simulation
OFDM 的整个流程的 仿真程序 适于初学者学习ofdm的整个过程()
- 2007-09-21 10:21:01下载
- 积分：1
-
pll
pll simulink model. noise and system model
- 2010-07-29 16:29:03下载
- 积分：1
