登录
首页 » Asm » 1.2

1.2

于 2014-01-07 发布 文件大小:2KB
0 112
下载积分: 1 下载次数: 1

代码说明:

  Indexing addrresses in NASM assembly

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • HW3000_EVB_SMA_V2.0A(433MHz)
    说明:  此原理图是验证过的PCB,波特率在1.2的时候功率20DB 时,空地上,离地面高度为10米左右,测试距离1000米左右(This schematic diagram is a PCB that has been verified. When the baud rate is 1.2, the power is 20dB. On the open ground, the height is about 10m from the ground and the test distance is about 1000m)
    2021-02-05 15:51:26下载
    积分:1
  • cn_mega8535-8535L
    高档AVR单片机Atmega8535中文资料,适合单片机初学者和开发者作参考资料。(upmarket AVR Atmega8535 Chinese data, MCU for beginners and developers for reference.)
    2007-02-03 16:12:47下载
    积分:1
  • lcd
    4寸LCD驱动,在uc-gui驱动的兼容,横屏竖屏直接配置,模拟驱动,直接使用(4-inch LCD driver, in ucgui drive compatibility, horizontal screen vertical screen directly configured, simulate drive)
    2015-12-10 09:56:40下载
    积分:1
  • SSD1289
    基于SSD1289控制器的液晶驱动程序,现在已经用在了产品上 保证好用(Based SSD1289 LCD controller driver now with a guarantee on the product easy to use)
    2014-06-06 23:23:18下载
    积分:1
  • EV_BIKE
    电动自行车锂电池使用保护板,方案实现文档(Electric bicycle lithium battery protection board, the program implementation document)
    2013-04-04 16:38:11下载
    积分:1
  • example6_TIM
    本例展示了如何设置TIM,用它来测量一个外部输入信号的频率和占空比。 TIM2时钟设置为72MHz,预分频设置为0,TIM2计数器时钟可表达为: TIM2 counter clock = TIMxCLK / (Prescaler +1) = 72 MHz,因此可测量的最小频率值为1100Hz。 设置TIM2工作在PWM输入模式(PWM Input Mode),把外部信号作为输入连接到TIM2通道2。 利用TIM2计数器中断来测量信号的频率和占空比。在TIM2_IRQHandler中,计算信号的频率和占空比,方法如下: 变量"Frequency"为由下式得到的外部信号频率: Frequency = TIM2 counter clock / TIM2_CCR2 单位Hz 变量"Duty_Cycle"为由下式得到的外部信号占空比: Duty_Cycle = (TIM2_CCR1*100)/(TIM2_CCR2) 单位 (This example shows how to set up the TIM, and use it to measure the frequency and duty cycle of an external input signal. TIM2 clock set to 72MHz and the prescaler is set to 0, TIM2 is counter clock can be expressed as: TIM2 is counter clock = TIMxCLK/(prescaler. Ppls1) = 72 MHz, the minimum measurable frequency value of 1100 Hz. Set TIM2 PWM input mode (PWM Input Mode), the external signal as an input connected to the the TIM2 Channel 2. TIM2 counter interrupt signal to measure frequency and duty cycle. Calculate the frequency and duty cycle of the signal in TIM2_IRQHandler as follows: variable " Frequency" on the grounds of the external signal frequency by the following formula: Frequency = TIM2 is counter clock/TIM2_CCR2 unit Hz variable Duty_Cycle " on the grounds of the following formula to get external duty cycle: Duty_Cycle = (TIM2_CCR1* 100)/(TIM2_CCR2) in )
    2012-05-18 18:28:47下载
    积分:1
  • ebike_load_test
    电动车控制器测功机随机产生器(可以模拟电动车实际路况进行寿命实验) 编译软件:WinAVR-20050214(Electric Bicycle Controller dynamometer random generator (which can simulate the actual road electric vehicles to perform a lifetime experiment) to compile the software: WinAVR-20050214)
    2009-12-26 11:59:38下载
    积分:1
  • stm32_w5300
    基于iCore2双核心板,用stm32和W5300实现以太网模块通讯。软件代码包括stm32驱动和Qt 程序。(Based iCore2 dual core board, with stm32 and W5300 Ethernet module communication. Stm32 drivers and software code, including Qt programs.)
    2021-04-21 20:28:49下载
    积分:1
  • PassTp
    内核重载过TP(看雪大牛作品,非常完整)(Kernel overloaded over TP (see snow Daniel works very complete))
    2015-03-06 19:36:29下载
    积分:1
  • Quectel_MC20_Hardware
    三合一模块,Mc20的硬件设计手册,已经通过做项目(Triad module, Mc20 hardware design manual, already by doing projects )
    2017-01-20 11:30:19下载
    积分:1
  • 696518资源总数
  • 106174会员总数
  • 31今日下载