登录
首页 » matlab » bianweichilun

bianweichilun

于 2012-02-24 发布 文件大小:1KB
0 183
下载积分: 1 下载次数: 11

代码说明:

  基于matlab,实现变位齿轮的精确建模(To achieve accurate modeling of variable gea)

文件列表:

bianweichilun.m,2965,2006-02-24

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • matlab制矩形、圆域、正六边形函数
    常用光瞳函数,矩形函数、圆域函数、正六边形函数、三角形函数的绘制(Commonly used pupil function, including rectangle function, circle function, hexagon function, triangle function)
    2021-04-20 19:48:50下载
    积分:1
  • 85301403
    多目标跟踪的Matlab仿真程序,用于数据处理和数据关联,不错的(Multiple target tracking of Matlab simulation program, used for data processing and data correlation, pretty good)
    2020-10-12 22:57:32下载
    积分:1
  • CSharp--HALCON-PAINT
    c#在HALCON 窗体上画图,任意图形。(c# in the HALCON form drawing, any graphics.)
    2015-07-15 09:36:24下载
    积分:1
  • UPFC_test
    基于PSCAD的UPFC模型,采用前馈解耦策略,有功无功基本独立控制,波形较好(Unified Power Flow Control Model based on PSCAD)
    2013-07-29 18:40:29下载
    积分:1
  • VF1MWL1MW
    这是pSCAD环境下的储能仿真模型,包含1MW的负载,对于为电网储能模型搭建有着很好的借鉴(This is a simulation model pSCAD storage environment, including 1MW load, grid energy storage for building model has a good reference)
    2021-04-11 14:38:58下载
    积分:1
  • Tquxian
    关于固高运动控制卡T曲线运动模式程序的例子(About Googol motion control card T curves sport program)
    2013-09-02 11:33:54下载
    积分:1
  • arim
    联合对角化方法,用于对多个矩阵同时进行联合对角化,主要用处是盲源分离,(Joint diagonalization method, is used to conduct joint diagonalization matrix at the same time for multiple, main use is to blind source separation,)
    2017-05-18 15:09:24下载
    积分:1
  • visio
    Visio 2010图形设计实战技巧精粹,让读者一目了然,更好地掌握Visio 2010。(Visio 2010 graphic design essence of combat skills, to give readers a glance, a better grasp of Visio 2010.)
    2013-11-18 20:23:36下载
    积分:1
  • dcsupply
    Design DC supply with filter circuit in PSCAD
    2016-11-17 22:31:53下载
    积分:1
  • jpaint-src-0.0.1
    这是国外的同行编写的画图板程序,感觉比陈建春的要好些,说实话研究了半天,发现国内的cad水平低不是因为国内的人笨,主要是国外的cad技术不能很快的传递到国人手中,总是参考陈建华等水平有限,工程水平差的书籍造成整体水平低,书中没有详细的流程图,和软件设计思路,而且代码错误连篇。(This is the foreign counterparts of the drawing board to prepare procedures, CHEN Jian-chun than feeling the need to better tell the truth for a long time study and found that low levels of domestic cad because people are not stupid, mainly abroad cad technology should not quickly delivered to the the hands of the people always refer to Chen Jianhua, such as the limited level, engineering level difference caused by the overall level of books low, the lack of a detailed flow chart of the book, and software design, and code errors pack.)
    2007-10-09 22:23:11下载
    积分:1
  • 696518资源总数
  • 106155会员总数
  • 8今日下载