-
basic-nandflash-project-at91sam9263-ek-keil
8bit nand flash interface for at91sam9263ek,其中编辑器为keil for mdk(8bit nand flash interface for at91sam9263ek, which editor for keil for mdk)
- 2009-02-15 21:12:25下载
- 积分：1
-
ARM_FGA_DEV
采用LPC的芯片做的气体排放检测,包括气体成分分析,数据的处理,数据传输给工作站.(LPC chips used to do the detection of gas emissions, including gas composition analysis, data processing, data transmission to the workstation.)
- 2008-08-05 20:14:20下载
- 积分：1
-
STM32-sm900a
stm32 sim900a 实现stm32拨打电话与接听电话(stm32 sim900a )
- 2020-08-28 13:38:12下载
- 积分：1
-
17_ADS8509
用STM32写的ADS8509的驱动,究竟调试完全通过。(Written with STM32 ADS8509 driver)
- 2020-11-01 10:39:54下载
- 积分：1
-
43-stm32_camera
基于stm32开发板的驱动 主要实现开发板上照相机的驱动。适用于新手( based on stm32 board driver it s about camera drivers,useful for fresh man )
- 2015-03-05 09:43:51下载
- 积分：1
-
STR710_programm_full_MDK
基于STR710的程序大全，编译环境为keil realview mdk!! (Guinness STR710-based procedures, the compiler environment keil realview mdk!!)
- 2008-03-09 19:26:51下载
- 积分：1
-
51
说明： 多点触摸，51例程。车载多媒体、数码产品上用(Multi-touch, 51 routines. Car multimedia, digital products with)
- 2011-10-20 16:19:39下载
- 积分：1
-
A-amplifier-arm-
设计的是一种基于ARM的自反馈程控放大器，它由ARM主控模块、放大模块、滤波模块、电源模块、键盘和液晶显示模块构成。以ARM1138作为主控芯片，通过对输出信号进行数据采集及处理，实现放大器增益校正与闭环控制，达到精确程控放大器增益和实时显示的目的(Design is a programmable ARM-based self-feedback amplifier, which consists of ARM control module, amplifier modules, filter modules, power modules, keyboard and LCD display modules. To ARM1138 as the master chip, the output signal by data acquisition and processing, calibration and closed-loop amplifier gain control, programmable amplifier gain to achieve accurate and real-time display purposes)
- 2011-09-02 15:48:09下载
- 积分：1
-
AD7190 STM32驱动
说明： AD7190驱动，使用STM32硬件SPI2接口。(The AD7190 driver uses the STM32 hardware SPI2 interface.)
- 2021-01-19 14:48:42下载
- 积分：1
-
AVR230_source
This is a simple bootloader for AT91SAM7 processors. It
permits you to download new code to the device over USB. This bootrom is
installed at address 0x00000000 in the ARM, which means that it is the
first piece of code to execute after reset. At startup, it waits for
a few seconds to see if the downloader is trying to connect. If not,
then the bootloader gives up control and jumps to your program. If the
downloader is trying to connect, then the bootloader receives the new
program over USB and writes it into flash.(This is a simple bootloader for AT91SAM7{S,X}{64,128,256} processors. It
permits you to download new code to the device over USB. This bootrom is
installed at address 0x00000000 in the ARM, which means that it is the
first piece of code to execute after reset. At startup, it waits for
a few seconds to see if the downloader is trying to connect. If not,
then the bootloader gives up control and jumps to your program. If the
downloader is trying to connect, then the bootloader receives the new
program over USB and writes it into flash.)
- 2009-11-17 10:47:55下载
- 积分：1
