登录
首页 » matlab » double-pendulum

double-pendulum

于 2014-01-13 发布 文件大小:2KB
0 170
下载积分: 1 下载次数: 5

代码说明:

  In order to model the chaotic motion of the double pendulum,i am going to use Matlab solving the problem using numerical methods such as Rung-Kutta and Ordinary Differential Equations (ODE).

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • tulunjigou
    说明:  MATLAB编写的凸轮机构绕中轴线旋转的程序(MATLAB prepared by the cam rotation axis around which the procedure)
    2006-05-14 09:06:38下载
    积分:1
  • Three-Ortogonal-Planes-(LPQ-TOP)
    spatio-temporal Local Phase Quantization Three Ortogonal Planes (LPQ-TOP)
    2011-10-25 16:29:52下载
    积分:1
  • MATLAB高阶谱分析信号处理工具箱
    信号阶谱分析,采用高阶分析处理信号,有效提取阶次信息(Signal order spectrum analysis, higher order analysis is used to process the signal, and the order information is extracted effectively)
    2020-11-26 20:09:31下载
    积分:1
  • Interpolation@Matlab
    插值法的matlab实现,内含说明。拉格朗日插值,均分牛顿插值,差分牛顿插值,三次样条插值,埃米尔特插值(Matlab interpolation method implementations, containing instructions. Lagrange interpolation, Newton interpolation sharing, differential Newton interpolation, cubic spline interpolation, Amy Stewart interpolation)
    2014-11-03 11:01:28下载
    积分:1
  • Matlab-senior-notes(5)
    Matlab高级讲义- SIMULINK仿真基础(Matlab senior notes- SIMULINK based simulation)
    2011-12-24 21:15:08下载
    积分:1
  • zibian_lyapunovE
    混沌时间序列的最大李雅普诺夫指数的求法,c-c算法(Chaotic time series of the largest Lyapunov exponent method, c-c algorithm)
    2021-02-27 00:39:37下载
    积分:1
  • exp
    小波分析,基于DWT的故障信号特征提取,可以画出条形图,多层分解(Wavelet analysis, DWT-based feature extraction of fault signal can draw bar charts, multi-decomposition)
    2020-09-12 09:47:59下载
    积分:1
  • DFTX1
    频谱分析中,高密度频谱和高分辨率频谱之间的区别(Spectrum analysis, the difference between the spectrum of high-density and high-resolution spectrum)
    2012-06-17 10:11:52下载
    积分:1
  • 2-Control
    For example, heating up the temperature in a room is a process that has the specific, desired outcome to reach and maintain a defined temperature (e.g. 20°C), kept constant over time. Here, the temperature is the controlled variable. At the same time, it is the input variable since it is measured by a thermometer and used to decide whether to heat or not to heat. The desired temperature (20°C) is the setpoint. The state of the heater (e.g. the setting of the valve allowing hot water to flow through it) is called the manipulated variable since it is subject to control action
    2013-08-16 16:53:45下载
    积分:1
  • 8-DIPUM-Code
    Basics in Image processing using MATLAB
    2009-06-09 12:36:05下载
    积分:1
  • 696518资源总数
  • 106215会员总数
  • 5今日下载