登录
首页 » matlab » invertedpendulumbymyself-

invertedpendulumbymyself-

于 2014-01-26 发布 文件大小:39KB
0 182
下载积分: 1 下载次数: 2

代码说明:

  imnverted pendulum bymyself it is used for simulation about robot

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • gui14
    通过底层代码实现绘制正弦余弦正切函数,并且带有清除按钮(Through the ground floor code realization draw sine cosine tangent function, and with a clear button)
    2012-04-06 16:23:58下载
    积分:1
  • QPSK
    有关通讯系统QPSK调制和解调理论值的仿真(QPSK modulation and demodulation in Matlab)
    2011-10-23 11:28:29下载
    积分:1
  • xbwmcwtd
    采用加权网络中节点强度和权重都是幂率分布的模型,加入重复控制,通过matlab代码,可以动态调节运行环境的参数,包括脚本文件和函数文件形式。( Using weighted model nodes in the network strength and weight are power law distribution, Join repetitive control, By matlab code, Can dynamically adjust the parameters of the operating environment, Including script files and function files in the form.)
    2016-03-22 23:41:00下载
    积分:1
  • GAandGASA
    关于蜂窝移动通信中频率分配的一个很有用的程序(Frequency allocation )
    2011-04-25 16:36:40下载
    积分:1
  • 2GPS_EKF
    design EKF for low cost INS/GPS
    2011-05-10 15:49:19下载
    积分:1
  • rayleigh_bpsk
    BPSK modulation in Rayleigh channel
    2013-09-19 20:34:05下载
    积分:1
  • C---Cookbook
    C ++ CODEBOOK 完整电子版,学习c++必备。(C++ CODEBOOK)
    2015-01-23 17:20:13下载
    积分:1
  • 电力系统暂态稳定分析序1
    说明:  本程序是暂态稳定分析程序,3机9节点模型,对其在pt时刻7号节点发生三相短路故障,并在ct时刻将故障切除进行仿真,最后绘出2号和1号发电机的功角差与时间的关系曲线。发电机模型采用三阶模型,忽略阻尼,电枢电阻取为零;励磁系统仅有量测和放大环节,忽略反馈和电压调节器;负荷采用恒定阻抗负荷。(This program is a transient stability analysis program, three machine nine node model, which has three-phase short circuit fault on node 7 at Pt time, and cut off the fault at CT time for simulation, and finally draw the relationship curve between power angle difference and time of generator 2 and 1. The generator model adopts the third-order model, neglecting the damping and taking the armature resistance as zero; the excitation system only has the measurement and amplification links, neglecting the feedback and voltage regulator; the load adopts the constant impedance load.)
    2020-06-02 12:54:47下载
    积分:1
  • Fec
    Forward error correction code algoritham for matlab codes
    2013-12-09 18:04:06下载
    积分:1
  • line_inter_3d
    使用Matlab的M文件编写的数控三轴直线运动代码,为验证DSP上的算法而编(Matlab M-file used to prepare three-axis linear motion of the CNC code, in order to verify the algorithm and the DSP for)
    2009-05-24 18:29:18下载
    积分:1
  • 696516资源总数
  • 106562会员总数
  • 4今日下载