-
用C语言编写STM32嵌入式程序 万年历 LCD
说明： 用C语言编写STM32嵌入式程序，设计一个万年历系统，并用HX1230屏显示相关的时间信息。
基本要求：
1.C语言程序要求是模块化设计。
2.该万年历要求能显示时间（时、分、秒）、年月日及闹钟定时时间（分、秒）。
3.该系统由2-3个按键可调整显示的时间、年月日及闹钟定时时间，具体各个按键功能及编程方式自定。
4.该闹钟可以定时时间到，LED将发出提示闪光，且持续30s。
5.HX1230屏能驱动显示。
6.定时时间可被打断，即打断后恢复时继续计时。
7.设置闹钟报警功能；
8.利用STM32自带的温度传感器功能，使系统能显示当前环境温度值。(STM32 embedded program is written in C language, a calendar system is designed, and relevant time information is displayed on HX1230 screen.
Basic requirements:
1. The requirement of C language program is modular design.
The calendar requires that time (hours, minutes, seconds), year, month, day and alarm clock timing time (minutes, seconds) be displayed.
3. The system can adjust the display time, year, month, day and alarm clock timing time by 2-3 keys, and the function and programming mode of each key are self-determined.
4. The alarm clock can be scheduled to arrive, and the LED will give a prompt to flash, and lasts for 30 seconds.
5. HX1230 screen can drive display.
6. Timing time can be interrupted, i.e. when the interruption is resumed, the timing will continue.
7. Setting alarm function of alarm clock;
8. Using the temperature sensor function of STM32, the system can display the current environmental temperature)
- 2020-06-25 05:00:02下载
- 积分：1
-
S1D13506_Init_code
Code demonstrating the initialization of the S1D13506 TFT Graphics display chip
- 2010-06-26 07:18:10下载
- 积分：1
-
16QAM
QAM调制模块，可用于Quartus仿真与fpga硬件实现。(QAM Modulation Mode, can be used for Quartus simulation and FPGA.)
- 2013-12-27 10:01:48下载
- 积分：1
-
实验7 定时器中断实验 - 同时TIM2 4
32 F429同时使用定时器2和4实现中断控制LED0和1闪烁(USING TIM2 AND TIM4 IN THE MEANWHILE)
- 2020-06-23 23:00:01下载
- 积分：1
-
240188modified-rom-based-logic
Modified rom based logic
- 2016-04-01 09:48:45下载
- 积分：1
-
The-virtual-oscilloscope
1、掌握利用A/D转换和计算机资源实现示波器的设计方法。
2、设计虚拟示波器。
3、建立NI-DAQmx仿真设备，选择E系列中的NI PCI-6071E数据采集卡的仿真模块，通过DAQmx物理通道识别，产生模拟信号，然后基于LabVIEW开发平台设计实现虚拟示波器。(1, master the use of A/D conversion and the design method of the computer resources to realize the oscilloscope.
2, the design of virtual oscilloscope.
3, establishment of NI- DAQmx simulation equipment, select the NI PCI- 6071- E E series simulation module of data acquisition card via DAQmx physical channel identification, produce analog signal, and then design the virtual oscilloscope based on LabVIEW development platform.)
- 2013-12-29 16:52:31下载
- 积分：1
-
MCUFPGACOM
单片机与FPGA的串口通信
单片机与FPGA的串口通信(MCU and FPGA-MCU and FPGA serial communication Serial communication)
- 2010-02-04 12:23:32下载
- 积分：1
-
dingshiqi
本程序采用C语言编程，利用proteus仿真实现定时器功能。(This program uses the C programming with proteus simulation clock function
)
- 2012-02-12 10:15:52下载
- 积分：1
-
24cxxx
本程序是24C128的51单片机读写程序。
测试芯片：at89s52
晶振：12MHz有keil、proteus文件和24c128的英文文档和详细注释(This procedure is 24C128 microcontroller to read and write program 51. Test chip: at89s52 crystal: 12MHz with keil, proteus file and 24c128 documents and detailed notes in English)
- 2010-09-02 15:44:51下载
- 积分：1
-
ARM_CAN232
实现简单的RS232 TO CAN,CAN T0 RS232的数据转换
(Realize a simple RS232 TO CAN, CAN T0 RS232 data conversion)
- 2008-07-18 19:24:34下载
- 积分：1
